1|Page
CSWA Simulation EXAM ||VERIFIED EXAM!!!|| MOST
RECENT EXAM 2026|2027 ACTUAL COMPLETE REAL
EXAM QUESTIONS AND CORRECT ANSWERS
(VERIFIED ANSWERS) ALREADY GRADED A+ |
GUARANTEED SUCCESS!! NEWEST EXAM!!
What is Yield Stress?
The stress level beyond which the material becomes
plastic
The stress level beyond which the material breaks
The strain level above the stress level which the material
breaks
The stress level beyond the melting point of the material -
Answer-The stress level beyond which the material
becomes plastic
A high-quality Shell element has ________ nodes.
,2|Page
4
5
6
8 - Answer-6
Stress σ is proportional to:
Strain
Stress
Force
Pressure - Answer-Strain
The Elastic Modulus (Young's Modulus) is the slope
defined as ________ divided by ________.
Strain, Stress
Stress, Strain
Stress, Force
Force, Area - Answer-Stress, Strain
,3|Page
Linear static analysis assumes that the relationship
between loads and the induced response is:
Flat
Linear
Doubles per area
Translational - Answer-Linear
In SOLIDWORKS Simulation, the Factor of Safety (FOS)
calculations are based on which of the following failure
criteria. Can be more than one answer.
Maximum von Mises Stress
Maximum shear stress
Mohr-Coulomb stress
Maximum Normal stress - Answer-Maximum von Mises
Stress
Maximum shear stress
Mohr-Coulomb stress
Maximum Normal stress
, 4|Page
The Yield point is the point where the material begins to
deform at a faster rate than at the elastic limit. The
material behaves ________ in the Plastic Range.
Flatly
Linearly
Non-Linearly
Like a liquid - Answer-Non-Linearly
What is the Modulus of Elasticity?
The slope of the Deflection-Stress Curve
The slope of the Stress-Strain curve in its linear section
The slope of the Force-Deflection curve in its linear
section
The first inflection point of a strain curve - Answer-The
slope of the Stress-Strain curve in its linear section
What is Stress?
CSWA Simulation EXAM ||VERIFIED EXAM!!!|| MOST
RECENT EXAM 2026|2027 ACTUAL COMPLETE REAL
EXAM QUESTIONS AND CORRECT ANSWERS
(VERIFIED ANSWERS) ALREADY GRADED A+ |
GUARANTEED SUCCESS!! NEWEST EXAM!!
What is Yield Stress?
The stress level beyond which the material becomes
plastic
The stress level beyond which the material breaks
The strain level above the stress level which the material
breaks
The stress level beyond the melting point of the material -
Answer-The stress level beyond which the material
becomes plastic
A high-quality Shell element has ________ nodes.
,2|Page
4
5
6
8 - Answer-6
Stress σ is proportional to:
Strain
Stress
Force
Pressure - Answer-Strain
The Elastic Modulus (Young's Modulus) is the slope
defined as ________ divided by ________.
Strain, Stress
Stress, Strain
Stress, Force
Force, Area - Answer-Stress, Strain
,3|Page
Linear static analysis assumes that the relationship
between loads and the induced response is:
Flat
Linear
Doubles per area
Translational - Answer-Linear
In SOLIDWORKS Simulation, the Factor of Safety (FOS)
calculations are based on which of the following failure
criteria. Can be more than one answer.
Maximum von Mises Stress
Maximum shear stress
Mohr-Coulomb stress
Maximum Normal stress - Answer-Maximum von Mises
Stress
Maximum shear stress
Mohr-Coulomb stress
Maximum Normal stress
, 4|Page
The Yield point is the point where the material begins to
deform at a faster rate than at the elastic limit. The
material behaves ________ in the Plastic Range.
Flatly
Linearly
Non-Linearly
Like a liquid - Answer-Non-Linearly
What is the Modulus of Elasticity?
The slope of the Deflection-Stress Curve
The slope of the Stress-Strain curve in its linear section
The slope of the Force-Deflection curve in its linear
section
The first inflection point of a strain curve - Answer-The
slope of the Stress-Strain curve in its linear section
What is Stress?
