OVERHEAD CRANE 2026 EXAMINERS SET
QUESTIONS AND ANSWERS SURE A+
✔✔manufacturer - ✔✔Who should establish a maintenance program for an overhead
crane?
✔✔during the shift - ✔✔When shall inspection of below the hook devices be performed?
✔✔ASME B30.20 - ✔✔Which of the ASME standards listed are for below the hook
lifting devices?
a) ASME B30.20
b) ASME B30.19
c) ASME B30.79
d) ASME B30.10
✔✔change battery at the beginning of the shift - ✔✔When preparing to use a remote or
radio control device, it is important to?
✔✔qualified person - ✔✔Who can authorize side loading of an overhead crane?
✔✔prevent strain on electric cord - ✔✔What is the purpose of a restraining cord used
on the pendant control box of an overhead crane?
, ✔✔pitting and wear - ✔✔When inspecting the electrical connectors on the trolley of an
overhead crane, which of the following is cause for concern?
a) No warning label.
b) Un-even welds.
c) Pitting and wear.
d) Lagging and wire rope.
✔✔the wire rope - ✔✔Which of the items listed below is effected the most by side
loading an overhead crane?
a) The trolley rails.
b) The wire rope.
c) The drum lagging.
d) The bridge girder.
✔✔spreader beam - ✔✔Long loads should be handled by which of these below the
hook lifting devices?
✔✔safe place out of the way - ✔✔Where is the best place to park an overhead crane?
✔✔palm up, fingers closed, thumb pointing in direction of motion, jerk the hand
horizontally - ✔✔Describe what signal is a Trolley Travel?
✔✔ its rated load marked on it - ✔✔Overhead cranes with more than one hoisting unit
shall have what?
✔✔removes power to entire crane - ✔✔What is the purpose of the "E" (Emergency)
stop on an overhead crane?
✔✔once a month - ✔✔How often does O.S.H.A. require a written wire rope inspection?
✔✔five - ✔✔Most loads should be rigged to within how many degrees of level?
✔✔5 to 1 - ✔✔According to ASME B30.2, what is the safety factor for rigging?
✔✔daily to monthly - ✔✔According to O.S.H.A. frequent Inspections shall be performed
when?
✔✔designated person - ✔✔According to ASME B30.2 a frequent inspection must be
performed by a?
✔✔10 degrees - ✔✔According to ASME B30.2, the maximum twist of the hook can't
exceed?
QUESTIONS AND ANSWERS SURE A+
✔✔manufacturer - ✔✔Who should establish a maintenance program for an overhead
crane?
✔✔during the shift - ✔✔When shall inspection of below the hook devices be performed?
✔✔ASME B30.20 - ✔✔Which of the ASME standards listed are for below the hook
lifting devices?
a) ASME B30.20
b) ASME B30.19
c) ASME B30.79
d) ASME B30.10
✔✔change battery at the beginning of the shift - ✔✔When preparing to use a remote or
radio control device, it is important to?
✔✔qualified person - ✔✔Who can authorize side loading of an overhead crane?
✔✔prevent strain on electric cord - ✔✔What is the purpose of a restraining cord used
on the pendant control box of an overhead crane?
, ✔✔pitting and wear - ✔✔When inspecting the electrical connectors on the trolley of an
overhead crane, which of the following is cause for concern?
a) No warning label.
b) Un-even welds.
c) Pitting and wear.
d) Lagging and wire rope.
✔✔the wire rope - ✔✔Which of the items listed below is effected the most by side
loading an overhead crane?
a) The trolley rails.
b) The wire rope.
c) The drum lagging.
d) The bridge girder.
✔✔spreader beam - ✔✔Long loads should be handled by which of these below the
hook lifting devices?
✔✔safe place out of the way - ✔✔Where is the best place to park an overhead crane?
✔✔palm up, fingers closed, thumb pointing in direction of motion, jerk the hand
horizontally - ✔✔Describe what signal is a Trolley Travel?
✔✔ its rated load marked on it - ✔✔Overhead cranes with more than one hoisting unit
shall have what?
✔✔removes power to entire crane - ✔✔What is the purpose of the "E" (Emergency)
stop on an overhead crane?
✔✔once a month - ✔✔How often does O.S.H.A. require a written wire rope inspection?
✔✔five - ✔✔Most loads should be rigged to within how many degrees of level?
✔✔5 to 1 - ✔✔According to ASME B30.2, what is the safety factor for rigging?
✔✔daily to monthly - ✔✔According to O.S.H.A. frequent Inspections shall be performed
when?
✔✔designated person - ✔✔According to ASME B30.2 a frequent inspection must be
performed by a?
✔✔10 degrees - ✔✔According to ASME B30.2, the maximum twist of the hook can't
exceed?
