Manual Trans COMPREHENSIVE QUESTIONS
AND ANSWERS | LATEST UPDATE | INSTANT
DOWNLOAD !
Save
Terms in this set (293)
In 1877, a patent for a(n) ________ FWD
carriage with a one-cylinder engine
was obtained by George Seldon.
In a front engine, rear-wheel drive 90
vehicle, the transmission sends power
to the final drive assembly, which
then changes the direction of the
twisting force ____ degrees so it can be
sent out the axles to the wheels and
tires.
Technician A says synchronizers are B
used to match the clutch and input
shaft speeds to provide easier gear
changes. Technician B says a
synchronizer matches gear speed
with shaft speed. Who is correct?
,Technician A states that early cars Both
with one-cylinder engine had one
belt-driven high gear for speed and
one belt-driven low gear for
increased torque. Technician B states
that if the car needed to climb a hill,
the driver had to stop, get out, and
change the belt to the lower gear.
Who is correct?
This early engine had one belt- The front-wheel drive carriage with a one-cylinder
driven high gear for speed, and one engine
belt-driven low gear for increased
torque:
Mechanical advantage can be used increase in input distance and speed.
to generate a larger output force, but
it requires a(n):
Technician A says gear ratios can be A
found by comparing the number of
teeth on the drive gear to those on
the driven gear. Technician B says
gears with the same number of teeth
have a ratio of 2:1. Who is correct?
All gear ratios are calculated by the driven gear divided by the drive gear.
formula:
Because of the _______, the Various gear sets
transmission/transaxle has multiple
paths along which the power can
flow.
, When tracing the power flow from Clutch assembly
the engine to the drive wheels, what
transmits power directly to the
transmission input shaft?
As transmission gear ratios are is decreased
changed, output torque and output
speed also change. If output speed
is increased, output torque:
The manual transmission receives clutch assembly.
power from the engine by way of the:
The purpose of the clutch safety allow the engine to be cranked only when the
switch is to: clutch pedal is depressed.
In a vehicle equipped with a manual engine
transmission, once a gear is selected,
the driver slowly releases the clutch
pedal and progressively connects
the ________ to the transmission.
Which of the following is affected by Both
the gear ratio of the final drive
assembly?
All of the following statements with releasing the clutch pedal closes the contacts of
respect to manual transmission are the clutch safety switch.
true EXCEPT:
A closed clutch safety switch allows crank
the starter motor to crank the engine
over when the driver turns the key to
the _____ position.
AND ANSWERS | LATEST UPDATE | INSTANT
DOWNLOAD !
Save
Terms in this set (293)
In 1877, a patent for a(n) ________ FWD
carriage with a one-cylinder engine
was obtained by George Seldon.
In a front engine, rear-wheel drive 90
vehicle, the transmission sends power
to the final drive assembly, which
then changes the direction of the
twisting force ____ degrees so it can be
sent out the axles to the wheels and
tires.
Technician A says synchronizers are B
used to match the clutch and input
shaft speeds to provide easier gear
changes. Technician B says a
synchronizer matches gear speed
with shaft speed. Who is correct?
,Technician A states that early cars Both
with one-cylinder engine had one
belt-driven high gear for speed and
one belt-driven low gear for
increased torque. Technician B states
that if the car needed to climb a hill,
the driver had to stop, get out, and
change the belt to the lower gear.
Who is correct?
This early engine had one belt- The front-wheel drive carriage with a one-cylinder
driven high gear for speed, and one engine
belt-driven low gear for increased
torque:
Mechanical advantage can be used increase in input distance and speed.
to generate a larger output force, but
it requires a(n):
Technician A says gear ratios can be A
found by comparing the number of
teeth on the drive gear to those on
the driven gear. Technician B says
gears with the same number of teeth
have a ratio of 2:1. Who is correct?
All gear ratios are calculated by the driven gear divided by the drive gear.
formula:
Because of the _______, the Various gear sets
transmission/transaxle has multiple
paths along which the power can
flow.
, When tracing the power flow from Clutch assembly
the engine to the drive wheels, what
transmits power directly to the
transmission input shaft?
As transmission gear ratios are is decreased
changed, output torque and output
speed also change. If output speed
is increased, output torque:
The manual transmission receives clutch assembly.
power from the engine by way of the:
The purpose of the clutch safety allow the engine to be cranked only when the
switch is to: clutch pedal is depressed.
In a vehicle equipped with a manual engine
transmission, once a gear is selected,
the driver slowly releases the clutch
pedal and progressively connects
the ________ to the transmission.
Which of the following is affected by Both
the gear ratio of the final drive
assembly?
All of the following statements with releasing the clutch pedal closes the contacts of
respect to manual transmission are the clutch safety switch.
true EXCEPT:
A closed clutch safety switch allows crank
the starter motor to crank the engine
over when the driver turns the key to
the _____ position.
