3/27/26, 8:57 PM SOS Mechanic Certification- Brakes Flashcards | Quizlet
SOS Mechanic Certification- Brakes
4.7 (6 reviews)
Save
1
St udents also studied
SOS Mechanic Certification- Suspen... Michigan State Brakes Certification Michigan Mechanic License Practice ... SOS brake & brakin
82 terms 83 terms 37 terms 84 terms
vincent_quinter0 Preview Sheldon_Bunnell Preview brooklyn_tate3 Preview Jwedde
Terms in this set (83)
Most 1995 & newer vehicles use which of the following types Sealed non-serviceable
of wheels bearings on non-drive wheel?
to test a vacuum power brake booster in the vehicle, you drop slightly and remain firm
should pump the brake pedal at least 4 times, hold the brake
pedal depressed, and start the engine. the brake pedal should:
You are installing a set of brake shoe linings that are not the Smaller and goes towards the front of the car.
same length. Traditionally, the primary shoe lining is:
A cracked or torn vacuum diaphragm in a brake power a hard pedal feel requiring very high pedal effort to stop
booster would most likely cause:
https://quizlet.com/628299545/sos-mechanic-certification-brakes-flash-cards/ 1/9
, 3/27/26, 8:57 PM SOS Mechanic Certification- Brakes Flashcards | Quizlet
A mechanic finds gear lube inside both rear brake drums on a A plugged axle
rear wheel drive vehicle. What is the most likely cause of this
problem?
Which of the following incorrect service procedures will cause master cylinder push rod adjusted too long
brake lock-up?
Which of the following describes the proper way to Pump the brake pedal at least 25 times (or more, depending on the manufacturer's
depressurized an ABS system? recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed technician use the parking brake to adjust shoes and the cable is stuck
and the drums machined. the most likely cause is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake run-out
measurement?
On a 3-channel system, which wheels are on the same circuit? both rear wheels
One way to test an ABS wheel speed signal is to use _____ on AC volts
your digital multimeter.
The key input for the ABS control module comes from the: wheel speed sensors
ABS speed sensor and sensor rings: should not be hammered or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced: when dampness is evident on the hose
Which of the following should be used to check for rotor Micrometer
thickness variation:
After rebuilding a master cylinder, the rod between the master adjusted properly
cylinder and booster should be:
https://quizlet.com/628299545/sos-mechanic-certification-brakes-flash-cards/ 2/9
SOS Mechanic Certification- Brakes
4.7 (6 reviews)
Save
1
St udents also studied
SOS Mechanic Certification- Suspen... Michigan State Brakes Certification Michigan Mechanic License Practice ... SOS brake & brakin
82 terms 83 terms 37 terms 84 terms
vincent_quinter0 Preview Sheldon_Bunnell Preview brooklyn_tate3 Preview Jwedde
Terms in this set (83)
Most 1995 & newer vehicles use which of the following types Sealed non-serviceable
of wheels bearings on non-drive wheel?
to test a vacuum power brake booster in the vehicle, you drop slightly and remain firm
should pump the brake pedal at least 4 times, hold the brake
pedal depressed, and start the engine. the brake pedal should:
You are installing a set of brake shoe linings that are not the Smaller and goes towards the front of the car.
same length. Traditionally, the primary shoe lining is:
A cracked or torn vacuum diaphragm in a brake power a hard pedal feel requiring very high pedal effort to stop
booster would most likely cause:
https://quizlet.com/628299545/sos-mechanic-certification-brakes-flash-cards/ 1/9
, 3/27/26, 8:57 PM SOS Mechanic Certification- Brakes Flashcards | Quizlet
A mechanic finds gear lube inside both rear brake drums on a A plugged axle
rear wheel drive vehicle. What is the most likely cause of this
problem?
Which of the following incorrect service procedures will cause master cylinder push rod adjusted too long
brake lock-up?
Which of the following describes the proper way to Pump the brake pedal at least 25 times (or more, depending on the manufacturer's
depressurized an ABS system? recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed technician use the parking brake to adjust shoes and the cable is stuck
and the drums machined. the most likely cause is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake run-out
measurement?
On a 3-channel system, which wheels are on the same circuit? both rear wheels
One way to test an ABS wheel speed signal is to use _____ on AC volts
your digital multimeter.
The key input for the ABS control module comes from the: wheel speed sensors
ABS speed sensor and sensor rings: should not be hammered or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced: when dampness is evident on the hose
Which of the following should be used to check for rotor Micrometer
thickness variation:
After rebuilding a master cylinder, the rod between the master adjusted properly
cylinder and booster should be:
https://quizlet.com/628299545/sos-mechanic-certification-brakes-flash-cards/ 2/9
