NEIEP 200 Final Exam 2 | Actual Questions and
Answers | 2026 Update | 100% Correct.
you are about to loosen a fishplate bolt. which wrench would be least likely to slip?
a. 6 point box end wrench
b. 12 point box end wrench
c. open end wrench
you are using a plumb line to check a rail for plumb. you find that at the top it measures 1"
and at the bottom it measures 1 1/4". what does this tell you?
a. the top of the rail needs to go towards the center
b. the top of the rail needs to go toward the wall
c. the bottom of the rail needs to go toward the wall
you are plumbing rails on a high rise installation. what type of plumb line should you use?
a. nylon string
b. monofilament wire
c. piano wire
you need to cut into a concrete wall. which tool should you use?
disc grinder with a diamond blade disc
you need to select a heavy duty drill for drilling 5/8" holes in a machine beam. what factor
determines the drill rating?
chuck size
,you are tasked with setting 3/4" concrete anchors. which type of drill should you use?
rotary hammer
you need to cut and 8ft section of 1/2" EMT conduit pipe. what would be the best tool for
the job?
hacksaw with 24 teeth per inch
you are directed to move oxy-acetylene cylinders from a storage area to a work site. what is
the proper way to transport them?
in an upright position
you are setting up welding equipment. what is the maximum psi that the regulator for the
acetylene gas may be adjusted to?
10-12 psi
you are using rollers to move a heavy elevator machine and are approaching a corner.
which technique should you use to maneuver around it?
angle front roller gradually and continue around the corner
you are preparing to unload a truck at the loading dock and the truck is 8" higher than the
dock. what do you do?
use a steel plate to span the gap
you just finished the surface inspection of a manila rope you will be using for hoisting. what
method should you use to conduct an internal inspection?
slightly untwist the strands
, you are preparing to hoist rails and are inspecting your manila rope. which of the following
is a good characteristic of manila rope?
a light yellow color with a silvery or pearly luster
a mechanic attaches a chainfall to a hoisting beam with a beam clamp. what happens to the
capacity of the hoisting beam?
it is reduced to 50% of original capacity
you are rigging elevator equipment with a sling angle of 60 degrees. you are using a
shouldered eye bolt with a tapped 1/2" diameter hole. once the shoulder is seated, what is
the minimum thread depth required?
at least 3/4"
you will be hoisting 1klbs with a single leg vertical hitch. what will the sling load be when
the load is in the air
1k lbs
you must attach a wire rope to a load by creating a loop with 3 u-bolt wire rope clips. how
should the clips be attached?
no nuts on a dead horse
you are using a bowline knot- what is one disadvantage of this knot
is can easily loosen when not loaded
you are preparing to lift a load and need to tie the ends of two ropes together. which knot
should you use?
Answers | 2026 Update | 100% Correct.
you are about to loosen a fishplate bolt. which wrench would be least likely to slip?
a. 6 point box end wrench
b. 12 point box end wrench
c. open end wrench
you are using a plumb line to check a rail for plumb. you find that at the top it measures 1"
and at the bottom it measures 1 1/4". what does this tell you?
a. the top of the rail needs to go towards the center
b. the top of the rail needs to go toward the wall
c. the bottom of the rail needs to go toward the wall
you are plumbing rails on a high rise installation. what type of plumb line should you use?
a. nylon string
b. monofilament wire
c. piano wire
you need to cut into a concrete wall. which tool should you use?
disc grinder with a diamond blade disc
you need to select a heavy duty drill for drilling 5/8" holes in a machine beam. what factor
determines the drill rating?
chuck size
,you are tasked with setting 3/4" concrete anchors. which type of drill should you use?
rotary hammer
you need to cut and 8ft section of 1/2" EMT conduit pipe. what would be the best tool for
the job?
hacksaw with 24 teeth per inch
you are directed to move oxy-acetylene cylinders from a storage area to a work site. what is
the proper way to transport them?
in an upright position
you are setting up welding equipment. what is the maximum psi that the regulator for the
acetylene gas may be adjusted to?
10-12 psi
you are using rollers to move a heavy elevator machine and are approaching a corner.
which technique should you use to maneuver around it?
angle front roller gradually and continue around the corner
you are preparing to unload a truck at the loading dock and the truck is 8" higher than the
dock. what do you do?
use a steel plate to span the gap
you just finished the surface inspection of a manila rope you will be using for hoisting. what
method should you use to conduct an internal inspection?
slightly untwist the strands
, you are preparing to hoist rails and are inspecting your manila rope. which of the following
is a good characteristic of manila rope?
a light yellow color with a silvery or pearly luster
a mechanic attaches a chainfall to a hoisting beam with a beam clamp. what happens to the
capacity of the hoisting beam?
it is reduced to 50% of original capacity
you are rigging elevator equipment with a sling angle of 60 degrees. you are using a
shouldered eye bolt with a tapped 1/2" diameter hole. once the shoulder is seated, what is
the minimum thread depth required?
at least 3/4"
you will be hoisting 1klbs with a single leg vertical hitch. what will the sling load be when
the load is in the air
1k lbs
you must attach a wire rope to a load by creating a loop with 3 u-bolt wire rope clips. how
should the clips be attached?
no nuts on a dead horse
you are using a bowline knot- what is one disadvantage of this knot
is can easily loosen when not loaded
you are preparing to lift a load and need to tie the ends of two ropes together. which knot
should you use?
