NEIEP 200 review| Actual Questions and Answers |
2026 Update | 100% Correct.
1 inch equals how many centimeters?
2.54 centimeters
1 inch equals how many mm
25.4
1 foot equals how many centimeters
30.48
what is the best choice to use for a chalk line?
cotton twine
when using a 6 point wrench what is less likely to happen?
slip or round
to get an accurate reading with a caliper when measuring cylinders, ensure the tool does
what?
span the center line of the object
true or false, the square shank on a convential screwdriver is used for tightening square
head screws.
False, the square shank provides a way to use a
wrench to develop additional torque. Use a wrench that is properly sized for the shank to prevent
slippage
,how many points per inch is probably a good choice for most construction work that
requires a crosscut wood saw
seven
The cutting force is applied on the (forward/return) stroke when using a hacksaw.
always apply force on
the forward stroke.
Osha requries that all portable toos to be connected to what?
GFCI
what speed drills are preferred for heavy duty drilling?
slower, this is because Slower drill speeds are preferred for hard materials because it
minimizes destructive heat buildup at the cutting tip of the drill bit.
when using a grinder for cutting through concrete use how kind of discs
diamond blade
what saws are useful for cutting heavy metal objects or rough cutting walls?
reciprocating saw/ sawzall
True or false. when cutting finished material with a reciprocating saw, the finished side
should be away from the blade housing to minimize splintering?
true
a #2 phillips tip screwdriver would be used for what size screw gauge sizes?
, no. 5-9
True or false. it is okay to look at a welding arc as long as you are are 15 feet away from the
person welding.
Never look at a welding arc without eye protection, even from a distance. The flash may burn the
retina of your eyes, causing
scarring and a permanent blind spot. Extreme exposure can cause total blindness.
regulators for acetylene gas should never be adjusted for a working pressure greater than
what psi
10-12 psi. acetylene is a very unstable gas, it is stored in cylinders packed with porous material
saturated with
acetone. Acetylene at pressures above 15 psi is extremely dangerous
always store welding cylinders in what position?
upright.
how must welding cylinders be separated when stored?
a minimum of 20' or by a noncombustible barrier at least 5' high, having a 1/2 hour fire rating.
what is the key to safe and efficient unloading and storing of materials?
planning
how should the shipping skids on heavy machinery be for storage.
left in place.
how should cardboard cartons be stored to prevent absorbing moisture?
2026 Update | 100% Correct.
1 inch equals how many centimeters?
2.54 centimeters
1 inch equals how many mm
25.4
1 foot equals how many centimeters
30.48
what is the best choice to use for a chalk line?
cotton twine
when using a 6 point wrench what is less likely to happen?
slip or round
to get an accurate reading with a caliper when measuring cylinders, ensure the tool does
what?
span the center line of the object
true or false, the square shank on a convential screwdriver is used for tightening square
head screws.
False, the square shank provides a way to use a
wrench to develop additional torque. Use a wrench that is properly sized for the shank to prevent
slippage
,how many points per inch is probably a good choice for most construction work that
requires a crosscut wood saw
seven
The cutting force is applied on the (forward/return) stroke when using a hacksaw.
always apply force on
the forward stroke.
Osha requries that all portable toos to be connected to what?
GFCI
what speed drills are preferred for heavy duty drilling?
slower, this is because Slower drill speeds are preferred for hard materials because it
minimizes destructive heat buildup at the cutting tip of the drill bit.
when using a grinder for cutting through concrete use how kind of discs
diamond blade
what saws are useful for cutting heavy metal objects or rough cutting walls?
reciprocating saw/ sawzall
True or false. when cutting finished material with a reciprocating saw, the finished side
should be away from the blade housing to minimize splintering?
true
a #2 phillips tip screwdriver would be used for what size screw gauge sizes?
, no. 5-9
True or false. it is okay to look at a welding arc as long as you are are 15 feet away from the
person welding.
Never look at a welding arc without eye protection, even from a distance. The flash may burn the
retina of your eyes, causing
scarring and a permanent blind spot. Extreme exposure can cause total blindness.
regulators for acetylene gas should never be adjusted for a working pressure greater than
what psi
10-12 psi. acetylene is a very unstable gas, it is stored in cylinders packed with porous material
saturated with
acetone. Acetylene at pressures above 15 psi is extremely dangerous
always store welding cylinders in what position?
upright.
how must welding cylinders be separated when stored?
a minimum of 20' or by a noncombustible barrier at least 5' high, having a 1/2 hour fire rating.
what is the key to safe and efficient unloading and storing of materials?
planning
how should the shipping skids on heavy machinery be for storage.
left in place.
how should cardboard cartons be stored to prevent absorbing moisture?
