API 570 Piping Inspector Certification Exam
Questions With Correct Answers (Verified
Answers) Plus Rationales 2026 Q&A | Instant
Download Pdf
1. What is the primary purpose of the API 570 Piping Inspection
Code?
A. To design new piping systems
B. To provide guidelines for the inspection, repair, alteration, and
rerating of in-service piping systems
C. To regulate welding procedures
D. To establish safety rules for construction sites
Rationale: API 570 specifically addresses the inspection, repair,
alteration, and rerating of in-service piping, not new construction or
general welding regulations.
2. What is the maximum allowable working pressure (MAWP) of a
pipe determined by?
A. Fluid type
, B. Pipe length
C. Pipe material, design, and temperature
D. Ambient conditions
Rationale: MAWP is calculated based on the material’s allowable
stress, pipe design, and operating temperature, as per ASME B31.3
and B31.1.
3. Which inspection method is most suitable for detecting internal
corrosion in carbon steel piping?
A. Visual inspection only
B. Radiographic testing
C. Ultrasonic thickness measurements
D. Magnetic particle testing
Rationale: Ultrasonic thickness (UT) testing is commonly used to
monitor wall loss due to corrosion in carbon steel piping.
4. How often should a piping system be inspected according to API
570?
A. Every month
B. Every 10 years
, C. Based on the risk assessment and service conditions
D. Only when failures occur
Rationale: API 570 requires inspection intervals to be established
based on risk assessment, considering corrosion rates, fluid type, and
operating conditions.
5. What is the primary factor in determining the inspection interval
for a corroding pipe?
A. Pipe diameter
B. Welding procedure
C. Corrosion rate
D. Pipe color
Rationale: Corrosion rate determines how quickly a pipe loses
thickness, directly influencing the inspection interval.
6. Which of the following is considered a “high-risk” piping system?
A. Low-pressure water lines
B. Pipes carrying flammable or toxic fluids under high
temperature or pressure
, C. Steam condensate lines
D. Compressed air lines
Rationale: High-risk piping is defined by the potential for severe
consequences in the event of failure, such as fire, toxicity, or
environmental hazards.
7. What is the purpose of a thickness measurement program?
A. To detect weld defects
B. To check pipe diameter
C. To monitor wall loss due to corrosion or erosion
D. To verify insulation thickness
Rationale: Thickness measurement programs focus on identifying wall
thinning to prevent leaks and failures.
8. When inspecting a weld, which of the following is the most critical
parameter?
A. Weld color
B. Weld size
C. Weld integrity and soundness
D. Pipe diameter
Questions With Correct Answers (Verified
Answers) Plus Rationales 2026 Q&A | Instant
Download Pdf
1. What is the primary purpose of the API 570 Piping Inspection
Code?
A. To design new piping systems
B. To provide guidelines for the inspection, repair, alteration, and
rerating of in-service piping systems
C. To regulate welding procedures
D. To establish safety rules for construction sites
Rationale: API 570 specifically addresses the inspection, repair,
alteration, and rerating of in-service piping, not new construction or
general welding regulations.
2. What is the maximum allowable working pressure (MAWP) of a
pipe determined by?
A. Fluid type
, B. Pipe length
C. Pipe material, design, and temperature
D. Ambient conditions
Rationale: MAWP is calculated based on the material’s allowable
stress, pipe design, and operating temperature, as per ASME B31.3
and B31.1.
3. Which inspection method is most suitable for detecting internal
corrosion in carbon steel piping?
A. Visual inspection only
B. Radiographic testing
C. Ultrasonic thickness measurements
D. Magnetic particle testing
Rationale: Ultrasonic thickness (UT) testing is commonly used to
monitor wall loss due to corrosion in carbon steel piping.
4. How often should a piping system be inspected according to API
570?
A. Every month
B. Every 10 years
, C. Based on the risk assessment and service conditions
D. Only when failures occur
Rationale: API 570 requires inspection intervals to be established
based on risk assessment, considering corrosion rates, fluid type, and
operating conditions.
5. What is the primary factor in determining the inspection interval
for a corroding pipe?
A. Pipe diameter
B. Welding procedure
C. Corrosion rate
D. Pipe color
Rationale: Corrosion rate determines how quickly a pipe loses
thickness, directly influencing the inspection interval.
6. Which of the following is considered a “high-risk” piping system?
A. Low-pressure water lines
B. Pipes carrying flammable or toxic fluids under high
temperature or pressure
, C. Steam condensate lines
D. Compressed air lines
Rationale: High-risk piping is defined by the potential for severe
consequences in the event of failure, such as fire, toxicity, or
environmental hazards.
7. What is the purpose of a thickness measurement program?
A. To detect weld defects
B. To check pipe diameter
C. To monitor wall loss due to corrosion or erosion
D. To verify insulation thickness
Rationale: Thickness measurement programs focus on identifying wall
thinning to prevent leaks and failures.
8. When inspecting a weld, which of the following is the most critical
parameter?
A. Weld color
B. Weld size
C. Weld integrity and soundness
D. Pipe diameter
