Pipe Fitters Test Bank Exam 2026 -2027\Latest
Update |Complete Questions & Correct Detailed
Answers \Verified 100% Graded A+
What is the length of pipe required to fabricate a 6" diameter schedule 40
pipe spool with one class 150# RFWN flange on one end, and one class
300# RFWN flange on the other end, with a face-to-face measurement of 18
1/2" (assume a 1/8 welder gap)
ANSWERS: 10 7/8
What is the standard torquing valve of the Victualic coupling bolts?
ANSWERS: NO torquing is required
At what dimension does a pipe begin to be measured by the outside
diameter?
ANSWERS: 14 inches
What is the 4th ordinate cutback measurement for a 3" diameter type 3
dummy leg on a 6" elbow
ANSWERS: 10 3/16
,What is the ratio of the distance that the ladder should be from the base
of the wall to the height where the ladder meets the wall.
ANSWERS: 1/4
Trenches MUST be designed, excavated, and shored according to
ANSWERS: OSHA standards
angles of any triangle add up to
ANSWERS: 180º
What is the travel on a rolling offset that has a Run of 18", a roll 24" and
height of 12"?
ANSWERS: 34 15/16
Which of the following is a quick opening
valve? Globe, Needle , Butterfly , Gate ?
ANSWERS: Butterfly
Find the lowest common denominator for 1/8 and 1/2
ANSWERS: 8
, A piping drawing that shows both side view and top view of a piping system is
ANSWERS: isometric
the movement of pipe that is caused by an increase in temperature is called
ANSWERS: Thermal expansion
A cold spring relieves..
ANSWERS:
Thermal expansion
How many feet apart must oxygen and fuel gas cylinders be stored,
unless the is a 5 ft high, 30 minute burn rated wall between them?
ANSWERS: 20
When performing a line break, first?
ANSWERS: break the bolts down & away from you
A pipe nipple is any length of threaded pipe that is shorter than..
ANSWERS: 12"
Update |Complete Questions & Correct Detailed
Answers \Verified 100% Graded A+
What is the length of pipe required to fabricate a 6" diameter schedule 40
pipe spool with one class 150# RFWN flange on one end, and one class
300# RFWN flange on the other end, with a face-to-face measurement of 18
1/2" (assume a 1/8 welder gap)
ANSWERS: 10 7/8
What is the standard torquing valve of the Victualic coupling bolts?
ANSWERS: NO torquing is required
At what dimension does a pipe begin to be measured by the outside
diameter?
ANSWERS: 14 inches
What is the 4th ordinate cutback measurement for a 3" diameter type 3
dummy leg on a 6" elbow
ANSWERS: 10 3/16
,What is the ratio of the distance that the ladder should be from the base
of the wall to the height where the ladder meets the wall.
ANSWERS: 1/4
Trenches MUST be designed, excavated, and shored according to
ANSWERS: OSHA standards
angles of any triangle add up to
ANSWERS: 180º
What is the travel on a rolling offset that has a Run of 18", a roll 24" and
height of 12"?
ANSWERS: 34 15/16
Which of the following is a quick opening
valve? Globe, Needle , Butterfly , Gate ?
ANSWERS: Butterfly
Find the lowest common denominator for 1/8 and 1/2
ANSWERS: 8
, A piping drawing that shows both side view and top view of a piping system is
ANSWERS: isometric
the movement of pipe that is caused by an increase in temperature is called
ANSWERS: Thermal expansion
A cold spring relieves..
ANSWERS:
Thermal expansion
How many feet apart must oxygen and fuel gas cylinders be stored,
unless the is a 5 ft high, 30 minute burn rated wall between them?
ANSWERS: 20
When performing a line break, first?
ANSWERS: break the bolts down & away from you
A pipe nipple is any length of threaded pipe that is shorter than..
ANSWERS: 12"
