1|Page
NEIEP 500 FINAL EXAM, ELEVATOR MECHANIC
EXAM, NEIEP 500 COMPLETE 100 QUESTIONS AND
ANSWERS, ELEVATOR SYSTEMS TEST, ELECTRICAL
AND MECHANICAL COMPONENTS, SAFETY
PROCEDURES, NEIEP 2025
You have received a large shipment of doors for a high-rise installation and
have to get them stored properly. Which of the following statements is
correct? - CORRECT ANSWER✔✔ Store the doors vertically on the long edge
When setting sills, which of the following statements applies? - CORRECT
ANSWER✔✔ Worth the effort to make a template to determine sill
locations on a high-rise
When setting sills in compliance with the ASME rules, what is the minimum
clearance allowed between the platform sill and Hostway sill? - CORRECT
ANSWER✔✔ ½ inch
When setting sills in compliance with ASME rules, what is the max
clearance allowed between the platform sill and hoisway sill? - CORRECT
ANSWER✔✔ 1 ½ inch
,2|Page
When setting sills, which of the following must be done? - CORRECT
ANSWER✔✔ If rough spots exist on the roughed floor, set the sill to finished
floor height to account for thickness of material
You are installing a door frame, which of the following statements applies? -
CORRECT ANSWER✔✔ Use plumb lines hanging from magnets to plumb the
side frames
After installing entrances frames are prior to the blocks being installed,
what is the next step in the procedure? - CORRECT ANSWER✔✔ Place a
spreader board with cloth or paper on the ends halfway up the frame
between side jams
What is the name of the code that is the accepted standard for all electrical
wiring in the United States? - CORRECT ANSWER✔✔ National Electrical
Code
What is the maximum distance between supports of a vertical raceway,
based on NEC Article 620-32? - CORRECT ANSWER✔✔ 15 feet
, 3|Page
What type of flex would be used to pipe a switch in a wet location? -
CORRECT ANSWER✔✔ Liquidtight Flex
What is the name for the complete metal system of duct, conduit and flex
that protects the wiring? - CORRECT ANSWER✔✔ Raceway
How is the work divided when planning piping and wiring of an elevator
installation? - CORRECT ANSWER✔✔ Hoistway, car and machine room
What document may be the only place to look for such information as type
of fixtures, car panel, fire service floor, etc? - CORRECT ANSWER✔✔ Job
abstract
What information is shown on a pull sheet? - CORRECT ANSWER✔✔
Terminal connections
Which type of diagram shows a simplified path from positive to negative for
all components in a circuit? - CORRECT ANSWER✔✔ Straight line
NEIEP 500 FINAL EXAM, ELEVATOR MECHANIC
EXAM, NEIEP 500 COMPLETE 100 QUESTIONS AND
ANSWERS, ELEVATOR SYSTEMS TEST, ELECTRICAL
AND MECHANICAL COMPONENTS, SAFETY
PROCEDURES, NEIEP 2025
You have received a large shipment of doors for a high-rise installation and
have to get them stored properly. Which of the following statements is
correct? - CORRECT ANSWER✔✔ Store the doors vertically on the long edge
When setting sills, which of the following statements applies? - CORRECT
ANSWER✔✔ Worth the effort to make a template to determine sill
locations on a high-rise
When setting sills in compliance with the ASME rules, what is the minimum
clearance allowed between the platform sill and Hostway sill? - CORRECT
ANSWER✔✔ ½ inch
When setting sills in compliance with ASME rules, what is the max
clearance allowed between the platform sill and hoisway sill? - CORRECT
ANSWER✔✔ 1 ½ inch
,2|Page
When setting sills, which of the following must be done? - CORRECT
ANSWER✔✔ If rough spots exist on the roughed floor, set the sill to finished
floor height to account for thickness of material
You are installing a door frame, which of the following statements applies? -
CORRECT ANSWER✔✔ Use plumb lines hanging from magnets to plumb the
side frames
After installing entrances frames are prior to the blocks being installed,
what is the next step in the procedure? - CORRECT ANSWER✔✔ Place a
spreader board with cloth or paper on the ends halfway up the frame
between side jams
What is the name of the code that is the accepted standard for all electrical
wiring in the United States? - CORRECT ANSWER✔✔ National Electrical
Code
What is the maximum distance between supports of a vertical raceway,
based on NEC Article 620-32? - CORRECT ANSWER✔✔ 15 feet
, 3|Page
What type of flex would be used to pipe a switch in a wet location? -
CORRECT ANSWER✔✔ Liquidtight Flex
What is the name for the complete metal system of duct, conduit and flex
that protects the wiring? - CORRECT ANSWER✔✔ Raceway
How is the work divided when planning piping and wiring of an elevator
installation? - CORRECT ANSWER✔✔ Hoistway, car and machine room
What document may be the only place to look for such information as type
of fixtures, car panel, fire service floor, etc? - CORRECT ANSWER✔✔ Job
abstract
What information is shown on a pull sheet? - CORRECT ANSWER✔✔
Terminal connections
Which type of diagram shows a simplified path from positive to negative for
all components in a circuit? - CORRECT ANSWER✔✔ Straight line
