Reading Blueprints TPC 101 Exam Questions Fully Solved Latest 2025
In section drawings, slanted crosshatch lines represent... - Answers cut surface pg 11
Which of the six simple machines is a "continuous lever" with equal arms? - Answers pulley
The thread specification 10-32 NC 1B LH indicated ______ threads per inch and an ______ thread. -
Answers 32; internal
In the specification 10-32 NC 1B, the screw has a ______ fit and a ______ handed thread. - Answers
loose; right
Sheaves are usually fitted with ______ belts. - Answers v-shaped
On a lathe, the compound test is the base for the... - Answers tool holder
A drawing that shows all the parts separated from one another is called a(n)... - Answers exploded view
On a lathe, the top and the swivel are the two main parts of a... - Answers compound rest
What kind of drawing compresses all the parts into a two-dimensional plane? - Answers orthographic
projection
A drawing may show all the shafts of a gear train in a single plane in order to ... - Answers avoid
confusion
The part in a duct that directs and spreads the air is called a(n)... - Answers diffuser
What kind of development is used for making a sheet metal piece with a constant taper? - Answers
radial line
Most industrial plants specify bearings in terms of ______. They specify distance in ______. - Answers
north; feet
The location of machinery and equipment in a building is shown on a ______. - Answers floor plan
Structural drawings of a building show its framework, floors, and ______. - Answers foundations
A vertical view of a building can be used as a flow diagram called a(n) ______ drawing. - Answers
elevation
Pascal's law states that the pressure at a hydraulic system point acts ______. - Answers equally in all
directions
If equal pressure acts on both the rod side and the cap side of a piston, which side receives more force?
- Answers cap side
Rapid pressure changes in a hydraulic system can be prevented by a(n) ______. - Answers accumulator
In section drawings, slanted crosshatch lines represent... - Answers cut surface pg 11
Which of the six simple machines is a "continuous lever" with equal arms? - Answers pulley
The thread specification 10-32 NC 1B LH indicated ______ threads per inch and an ______ thread. -
Answers 32; internal
In the specification 10-32 NC 1B, the screw has a ______ fit and a ______ handed thread. - Answers
loose; right
Sheaves are usually fitted with ______ belts. - Answers v-shaped
On a lathe, the compound test is the base for the... - Answers tool holder
A drawing that shows all the parts separated from one another is called a(n)... - Answers exploded view
On a lathe, the top and the swivel are the two main parts of a... - Answers compound rest
What kind of drawing compresses all the parts into a two-dimensional plane? - Answers orthographic
projection
A drawing may show all the shafts of a gear train in a single plane in order to ... - Answers avoid
confusion
The part in a duct that directs and spreads the air is called a(n)... - Answers diffuser
What kind of development is used for making a sheet metal piece with a constant taper? - Answers
radial line
Most industrial plants specify bearings in terms of ______. They specify distance in ______. - Answers
north; feet
The location of machinery and equipment in a building is shown on a ______. - Answers floor plan
Structural drawings of a building show its framework, floors, and ______. - Answers foundations
A vertical view of a building can be used as a flow diagram called a(n) ______ drawing. - Answers
elevation
Pascal's law states that the pressure at a hydraulic system point acts ______. - Answers equally in all
directions
If equal pressure acts on both the rod side and the cap side of a piston, which side receives more force?
- Answers cap side
Rapid pressure changes in a hydraulic system can be prevented by a(n) ______. - Answers accumulator
