1|Page
POWER ENGINEERING PRACTICE
EXAM (CHEMICAL ENGINEERING)
TEST BANK / FULL ACTUAL GUIDE
EXPERT VERIFIED QUESTIONS &
CERTIFIED SOLUTIONS / NEWEST
UPDATED 2025/2026
Two canadadian codes which have been adopted by all canadian
jurisdictions and which are of importance to fifth class power
engineering are the:
-..........ANSWER...........CSA B51 And B52
The ASME code sections which are most pertinent to Fifth and Fourth
class power engineer are sections:
-..........ANSWER...........IV and VI
what code contains guidelines for the care and operation of heating
boilers?
-..........ANSWER...........ASME Section VI
When a feedwater pump feeds two of more boilers from a common
source, there must be a regulating valve
-..........ANSWER...........Each feedwater line to each boiler
,2|P age
what determines the classification of the certificate of completency
required for the role of chief power engineer? -
..........ANSWER...........Kilowatt rating of the powerplant
The provincial regulations require that all welding repairs on boilers
must be:
-..........ANSWER...........approved by an authorized inspector
A boiler in which steam is made at a present not greater than 103
Kilopascals, is properly termed a:
-..........ANSWER...........heating plant
In the power engineers regulations definitions, ______ means any part of
the surface of a boiler that is in contact with fluid under pressure on one
side and the products of combustion on the other side: -
..........ANSWER...........Heating surface
Heating plant means one or more boilers in which water that can be
heated pressure and temperature of not more than: -
..........ANSWER...........1,100 kPa and a temp of 121c
The letters CRN stands for
-..........ANSWER...........Canadian registration number
Heat passes through the metal of heating surfaces by: -
..........ANSWER...........conduction
,3|P age
Six kg would be a measure of an object's:
-..........ANSWER...........mass
the term used to describe the fluid to gas change of state during the
addition of heat is latent heat of:
-..........ANSWER...........evapotarion
the fahrenheit scale considers the boiling point of water to be -
..........ANSWER...........212c
The three meathods of heat transfer are: -
..........ANSWER...........Radiation, conduction and convection
Water extinguishes a fire by:
-..........ANSWER...........cooling the combustible material
Water hammer can be prevented or minimized by installing___
chambers on a piping system.
-..........ANSWER..........."end of line" air
when working below ground level, the work presents the danger of : -
..........ANSWER...........falling objects
, 4|P age
Under WHMIS legislation all workers have the right to -
..........ANSWER...........Know what material they are working with
of the following materials, which would be classified as a class B fire? -
..........ANSWER...........Paper
The correct safe working angle for a ladder is:
-..........ANSWER...........1 to 4
overhead work presents the danger of ____ to others in the area. -
..........ANSWER...........falling objects
The damaging factor of an electrical circuit is the: -
..........ANSWER...........current
It is important to know the location of the main shut off valve to the
main water supple line feed to a building:
-..........ANSWER...........If it becomes necessary to shut the water supply
to repair a major leak
To reach high windows for cleaning it is appropriate to use: -
..........ANSWER...........approved ladders and scaffoldings
when changing an expansion tank gage class, a worker should utilize a: -
..........ANSWER...........face shield
POWER ENGINEERING PRACTICE
EXAM (CHEMICAL ENGINEERING)
TEST BANK / FULL ACTUAL GUIDE
EXPERT VERIFIED QUESTIONS &
CERTIFIED SOLUTIONS / NEWEST
UPDATED 2025/2026
Two canadadian codes which have been adopted by all canadian
jurisdictions and which are of importance to fifth class power
engineering are the:
-..........ANSWER...........CSA B51 And B52
The ASME code sections which are most pertinent to Fifth and Fourth
class power engineer are sections:
-..........ANSWER...........IV and VI
what code contains guidelines for the care and operation of heating
boilers?
-..........ANSWER...........ASME Section VI
When a feedwater pump feeds two of more boilers from a common
source, there must be a regulating valve
-..........ANSWER...........Each feedwater line to each boiler
,2|P age
what determines the classification of the certificate of completency
required for the role of chief power engineer? -
..........ANSWER...........Kilowatt rating of the powerplant
The provincial regulations require that all welding repairs on boilers
must be:
-..........ANSWER...........approved by an authorized inspector
A boiler in which steam is made at a present not greater than 103
Kilopascals, is properly termed a:
-..........ANSWER...........heating plant
In the power engineers regulations definitions, ______ means any part of
the surface of a boiler that is in contact with fluid under pressure on one
side and the products of combustion on the other side: -
..........ANSWER...........Heating surface
Heating plant means one or more boilers in which water that can be
heated pressure and temperature of not more than: -
..........ANSWER...........1,100 kPa and a temp of 121c
The letters CRN stands for
-..........ANSWER...........Canadian registration number
Heat passes through the metal of heating surfaces by: -
..........ANSWER...........conduction
,3|P age
Six kg would be a measure of an object's:
-..........ANSWER...........mass
the term used to describe the fluid to gas change of state during the
addition of heat is latent heat of:
-..........ANSWER...........evapotarion
the fahrenheit scale considers the boiling point of water to be -
..........ANSWER...........212c
The three meathods of heat transfer are: -
..........ANSWER...........Radiation, conduction and convection
Water extinguishes a fire by:
-..........ANSWER...........cooling the combustible material
Water hammer can be prevented or minimized by installing___
chambers on a piping system.
-..........ANSWER..........."end of line" air
when working below ground level, the work presents the danger of : -
..........ANSWER...........falling objects
, 4|P age
Under WHMIS legislation all workers have the right to -
..........ANSWER...........Know what material they are working with
of the following materials, which would be classified as a class B fire? -
..........ANSWER...........Paper
The correct safe working angle for a ladder is:
-..........ANSWER...........1 to 4
overhead work presents the danger of ____ to others in the area. -
..........ANSWER...........falling objects
The damaging factor of an electrical circuit is the: -
..........ANSWER...........current
It is important to know the location of the main shut off valve to the
main water supple line feed to a building:
-..........ANSWER...........If it becomes necessary to shut the water supply
to repair a major leak
To reach high windows for cleaning it is appropriate to use: -
..........ANSWER...........approved ladders and scaffoldings
when changing an expansion tank gage class, a worker should utilize a: -
..........ANSWER...........face shield
