NACE CIP 1 CBT EXAM PRACTICE 2025/2026 ACTUAL
COMPLETE REAL EXAM QUESTIONS & CORRECT
ANSWERS (VERIFIED ANSWERS) ALREADY
GRADED A+ | NEWEST VERSION
| JUST RELEASED!!
Which one of these elements is not necessary for
corrosion to occur: -
ANSWER-Reference
Cell
When using a sling psychrometer a very large difference
between the wet and
dry bulb readings indicates: - ANSWER-Low
Relative Humidity
The NACE Inspector should perform tests for soluble salts: -
ANSWER-When
specified.
,Corrosion generally occurs at which of the following sites: -
ANSWER-Anode
If Inspectors identify issues of non conformance during an
inspection, they should: - ANSWER-Inform both the Contractor
and the inspectors supervisor so they can take appropriate
corrective actions.
You are the NACE Inspector on a job where ISO ST 3 has been
specified. The Contractor normally works to SSPC standards
and been referencing SSPC SP 3. Could this have any impact
on the final surface preparation appearance? - ANSWER-No,
because there is no real difference in the standards.
Safety Data Sheets must be carefully reviewed by: -
ANSWER-All personal
involved in the
job.
You are the NACE Inspector on a job where the Owner's
specification requires you to perform a twice daily check of the
blast pressure at the nozzle. It is now day 30 on the job and all
your readings have been within compliance. The contractor
complains that these checks are taking up to much time and in
view of the compliant results they are unnecessary. Your FIRST
,preferred course of action is to: - ANSWER-Keep doing the
checks and consult the Owner's representative for direction.
If the project specification DOES NOT state the specific DFT
measurement
standards, the inspector should use: - ANSWER-A
recognized industry
standard like SSPC-PA 2 that is broadly
accepted.
ISO SA 2 is defined as: - ANSWER-Thorough Blast Cleaning
When using the ISO comparator in accordance with ISO 8503, if
the surface profile does not directly compare to the one of the
four segments the inspector should: - ANSWER-Record your
result by identifying two segments.
Owners hire NACE Inspectors with the expectation that: -
ANSWER-The inspection cost will be offset by an improvement
in service life and The inspector will make a meaningful
technical contribution to the job.
An inspector should change position when: - ANSWER-
The inspector is
, convinced by verifiable
facts.
Solventborne inorganic zinc primer is being applied with airless
spray to complex bride with difficult access for application. The
contractor is having difficulty with hight DFT resulting in
mkudcracking. What application method might be a good
alternative? - ANSWER-Conventional Spray
When reporting the wet film thickness from a wet film
thickness comb/gauge
(WFT) you report? - ANSWER-The last tooth that has
coating on it.
Adding an incorrect solvent to a coating may cause? -
ANSWER-Non drying
and non
curing.
You are reviewing the documentation for a tank waiting project
and notice there is a conflict between the project specification
and the manufacture's product data sheet on the required DFT
of the primer. The owner is not reachable for clarification. What
should be done? - ANSWER-Follow the specification.
COMPLETE REAL EXAM QUESTIONS & CORRECT
ANSWERS (VERIFIED ANSWERS) ALREADY
GRADED A+ | NEWEST VERSION
| JUST RELEASED!!
Which one of these elements is not necessary for
corrosion to occur: -
ANSWER-Reference
Cell
When using a sling psychrometer a very large difference
between the wet and
dry bulb readings indicates: - ANSWER-Low
Relative Humidity
The NACE Inspector should perform tests for soluble salts: -
ANSWER-When
specified.
,Corrosion generally occurs at which of the following sites: -
ANSWER-Anode
If Inspectors identify issues of non conformance during an
inspection, they should: - ANSWER-Inform both the Contractor
and the inspectors supervisor so they can take appropriate
corrective actions.
You are the NACE Inspector on a job where ISO ST 3 has been
specified. The Contractor normally works to SSPC standards
and been referencing SSPC SP 3. Could this have any impact
on the final surface preparation appearance? - ANSWER-No,
because there is no real difference in the standards.
Safety Data Sheets must be carefully reviewed by: -
ANSWER-All personal
involved in the
job.
You are the NACE Inspector on a job where the Owner's
specification requires you to perform a twice daily check of the
blast pressure at the nozzle. It is now day 30 on the job and all
your readings have been within compliance. The contractor
complains that these checks are taking up to much time and in
view of the compliant results they are unnecessary. Your FIRST
,preferred course of action is to: - ANSWER-Keep doing the
checks and consult the Owner's representative for direction.
If the project specification DOES NOT state the specific DFT
measurement
standards, the inspector should use: - ANSWER-A
recognized industry
standard like SSPC-PA 2 that is broadly
accepted.
ISO SA 2 is defined as: - ANSWER-Thorough Blast Cleaning
When using the ISO comparator in accordance with ISO 8503, if
the surface profile does not directly compare to the one of the
four segments the inspector should: - ANSWER-Record your
result by identifying two segments.
Owners hire NACE Inspectors with the expectation that: -
ANSWER-The inspection cost will be offset by an improvement
in service life and The inspector will make a meaningful
technical contribution to the job.
An inspector should change position when: - ANSWER-
The inspector is
, convinced by verifiable
facts.
Solventborne inorganic zinc primer is being applied with airless
spray to complex bride with difficult access for application. The
contractor is having difficulty with hight DFT resulting in
mkudcracking. What application method might be a good
alternative? - ANSWER-Conventional Spray
When reporting the wet film thickness from a wet film
thickness comb/gauge
(WFT) you report? - ANSWER-The last tooth that has
coating on it.
Adding an incorrect solvent to a coating may cause? -
ANSWER-Non drying
and non
curing.
You are reviewing the documentation for a tank waiting project
and notice there is a conflict between the project specification
and the manufacture's product data sheet on the required DFT
of the primer. The owner is not reachable for clarification. What
should be done? - ANSWER-Follow the specification.
