Page 1 of 40
Automotive collision ase practice
exam latest 2024-2025 with all
300 questions and correct
detailed answers (verified
answers)| graded a+
Technician A says that when replacing metal parts, an anti-corosion
material should be applied. Technician B says that some adhesive
products may contain anti-corrosion properties. Who is right?
A. A only
B. B only
C. Both A and B
D, Neither A nor B ✔✔✔✔✔✔ANSWER➖C. Both A and B
Technician A says that humidity can influence the rate of corrosion.
Technician B says that cold temperatures can accelerate the rate of
corrosion. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B ✔✔✔✔✔✔ANSWER➖A. A only
, Page 2 of 40
Which of these is the best method to correct a filler weld with too little
penetration?
A. Increase the stick-out and increase the wire feed
B. Increase the drive roll pressure and decrease the stick-out
C. Decrease the drive speed and increase the heat and wire feed
D. Increase the drive speed and decrease the stick-out
✔✔✔✔✔✔ANSWER➖A. increase the stick-out and increase the wire
feed
Which of these tools should be used to metal finish a damaged panel?
A. Pick hammer and a vixen file
B. A grater and in-line sander
C. An electric sander with 16-grit sandpaper
D. A stud pin welder ✔✔✔✔✔✔ANSWER➖B. A grater and in-line
sander
Which of these characteristics would be the most noticeable difference
when metal finishing aluminum versus steel?
A. Work hardening
B. Ambient temperature
C. Location of damage
D. Alloy composition ✔✔✔✔✔✔ANSWER➖D. Alloy composition
, Page 3 of 40
When used to cut off a metal panel which of these tools would generate
the least amount of heat?
A. cut-off wheel
B. Plasma cutting torch
C. Air saw
D. Oxyacetylene cutting torch ✔✔✔✔✔✔ANSWER➖A. Air saw
Which of these products can be applied over the manufacturer's finish?
A. Fiberglass fillers
B. Aluminum fillers
C. Polyester glazing putty
D. talc fillers ✔✔✔✔✔✔ANSWER➖C. Polyester glazing putty
Which of these methods of attachment would be used for composite
panels?
A. Weld bonding
B. Self-piercing rivets
C. Panel bonding
D. Lamination ✔✔✔✔✔✔ANSWER➖C. Panel bonding
Direct damage and indirect damage are also known as:
, Page 4 of 40
A. existing and pre-existing
B. asymmetrical and symmetrical
C. Literal and unilateral
D. Primary and secondary ✔✔✔✔✔✔ANSWER➖B. asymmetrical and
symmetrical
The following question contains the word EXCEPT. Please read the
question carefully and look for the choice that could NOT cause the
described situation.
A. cover the panel with welding blankets
B. remove any parts that can be removed
C. use shields to protect the panels
D. spray with water during the welding and cutting process
✔✔✔✔✔✔ANSWER➖D. spray with water during the welding and
cutting process
Technician A says that laminated glass may be used for the front
windshield. Technician B says that tempered glass may be used for door
glass. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B ✔✔✔✔✔✔ANSWER➖C. Both A and B
Automotive collision ase practice
exam latest 2024-2025 with all
300 questions and correct
detailed answers (verified
answers)| graded a+
Technician A says that when replacing metal parts, an anti-corosion
material should be applied. Technician B says that some adhesive
products may contain anti-corrosion properties. Who is right?
A. A only
B. B only
C. Both A and B
D, Neither A nor B ✔✔✔✔✔✔ANSWER➖C. Both A and B
Technician A says that humidity can influence the rate of corrosion.
Technician B says that cold temperatures can accelerate the rate of
corrosion. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B ✔✔✔✔✔✔ANSWER➖A. A only
, Page 2 of 40
Which of these is the best method to correct a filler weld with too little
penetration?
A. Increase the stick-out and increase the wire feed
B. Increase the drive roll pressure and decrease the stick-out
C. Decrease the drive speed and increase the heat and wire feed
D. Increase the drive speed and decrease the stick-out
✔✔✔✔✔✔ANSWER➖A. increase the stick-out and increase the wire
feed
Which of these tools should be used to metal finish a damaged panel?
A. Pick hammer and a vixen file
B. A grater and in-line sander
C. An electric sander with 16-grit sandpaper
D. A stud pin welder ✔✔✔✔✔✔ANSWER➖B. A grater and in-line
sander
Which of these characteristics would be the most noticeable difference
when metal finishing aluminum versus steel?
A. Work hardening
B. Ambient temperature
C. Location of damage
D. Alloy composition ✔✔✔✔✔✔ANSWER➖D. Alloy composition
, Page 3 of 40
When used to cut off a metal panel which of these tools would generate
the least amount of heat?
A. cut-off wheel
B. Plasma cutting torch
C. Air saw
D. Oxyacetylene cutting torch ✔✔✔✔✔✔ANSWER➖A. Air saw
Which of these products can be applied over the manufacturer's finish?
A. Fiberglass fillers
B. Aluminum fillers
C. Polyester glazing putty
D. talc fillers ✔✔✔✔✔✔ANSWER➖C. Polyester glazing putty
Which of these methods of attachment would be used for composite
panels?
A. Weld bonding
B. Self-piercing rivets
C. Panel bonding
D. Lamination ✔✔✔✔✔✔ANSWER➖C. Panel bonding
Direct damage and indirect damage are also known as:
, Page 4 of 40
A. existing and pre-existing
B. asymmetrical and symmetrical
C. Literal and unilateral
D. Primary and secondary ✔✔✔✔✔✔ANSWER➖B. asymmetrical and
symmetrical
The following question contains the word EXCEPT. Please read the
question carefully and look for the choice that could NOT cause the
described situation.
A. cover the panel with welding blankets
B. remove any parts that can be removed
C. use shields to protect the panels
D. spray with water during the welding and cutting process
✔✔✔✔✔✔ANSWER➖D. spray with water during the welding and
cutting process
Technician A says that laminated glass may be used for the front
windshield. Technician B says that tempered glass may be used for door
glass. Who is right?
A. A only
B. B only
C. Both A and B
D. Neither A nor B ✔✔✔✔✔✔ANSWER➖C. Both A and B
