Mechanics Exam NEIEP_ Exam Questions and Answers updated and Already Graded A+ 100%

Mechanics Exam NEIEP_ Exam Questions and Answers updated and Already Graded A+ 100% Mechanics-NEIEP ** An MOV burns out, you replace it but cannot read voltage or resistance. What should you do? - CORRECT ANSWER-Replace it with a larger one (630) * On a Ward-Leonard circuit, the brake is set but the motor is trying to slip through the brake. What circuit is the issue? - CORRECT ANSWER-Suicide circuit (425) ** A Hydro runs up with no load but does not run up with a full load. What is the issue? - CORRECT ANSWER-The relief valve is set too low (805) ** Runby for a 1:1 car hits the CWT buffer 4" below the top landing. The CWT runby should be set at 18". How much should the ropes be shortened? - CORRECT ANSWER-22" for 1:1. For a 2:1 with the same issue is 44". ** You need to work on a freight door retiring cam. You LOTO the mainline disconnect but there is still power to the cam. What circuit is still hot? - CORRECT ANSWER-Mainline disconnect (535) ** The contractor requests that the vertical center of the Rack and Pinion hoist be moved. How is this accomplished? - CORRECT ANSWER-Adjust Tie downs/Wall ties (805) ** Working pressure on a Hydro is 400 PSI. What is the correct Relief Valve Setting? - CORRECT ANSWER-600 PSI Max. (805) 400 psi x 150% = 600 psi ** A contractor wants to raise the car speed from 100 FPM to 125 FPM. It currently has a 12" sheave. What size sheave is required? - CORRECT ANSWER-15" (125 /100 = 1.25 1.25 x 12 = 15) ** There is slight arcing at the Brushes and Commutator. What actions must be taken? - CORRECT ANSWER-None. (430) "Heavy arcing is due to light brush pressure. Mechanical wear indicates heavy brush pressure. ** How much resistance is normally measured across a normally closed switch ? - CORRECT ANSWER-1.2 ohms or 1 to 2 ohms ** A car traveling in the hoistway always stops at the same point and blows a fuse. What is the problem? - CORRECT ANSWER-Traveling cable has a cut or short ** How is a Class 1 (yearly) buffer test performed? - CORRECT ANSWER-At slow speed and the buffer must return in 90 seconds. (555) *(60 seconds is acceptable) (90 seconds is code) 5 year test (Class 5) is car at rated load and speed. Buffer must return in 90 seconds. CWT at rated speed and buffer must return in 90 seconds. ** How many Strain Supports are required on a 350' raceway? - CORRECT ANSWER-4 One for every 100' ** How is Stainless steel drilled out? - CORRECT ANSWER-Slow speed and constant pressure (205) ** What are the required amount of clips for Wedge Shackles and what is their spacing? - CORRECT ANSWER-At least 2, with the first being 4 times the diameter of the rope from the top of shackle. Second is 8 times the diameter of the rope from the first. ** Car is loaded with 125% and sinks. Why? - CORRECT ANSWER-Slipped through the brake. ** A 300 Ohm resistor burns out. You don't have a 300 Ohm resistor to replace it. What can you use to make up the resistor? - CORRECT ANSWER-2 600 Ohms resistors in Parallel. "The resistance is half of the highest rating in a parallel circuit. 3, 225 Ohm resistors in parallel equal 75 Ohms. ** A 480 VAC Step Down Transformer is connected to a 3 phase rectifier. What will the output be? - CORRECT ANSWER-320 VDC 480 - 33.33% = 320 ** If you find a broken or missing barricade, what do you do? - CORRECT ANSWER-Write up a formal inspection request. ** If a Dumbwaiter has 9 square feet in Area, 4 ' High and the rated Capacity is 13.9 lb/ft3, what is the total capacity? - CORRECT ANSWER-500 lb/ft3. "The area of a Dumbwaiter is 9 sq' max and is 4' High. Multiply that by 13.9. 9x4 = 36. 36 x 13.9 = 500 ** What are the consequences of a misaligned Rack and Pinion hoist joint? - CORRECT ANSWER-Broken Gear Teeth (850) Motor not aligned. ** You enter a Pit where toxic fumes are present. How do you proceed? - CORRECT ANSWER-Follow proper procedures.