NABCEP: System Installation and
Inspection (Module 4 Review)
True or False? Some of the maximum vital matters to check when preparing for a solar panel
set up activity are the building allows
True
1 more than one choice alternative
The low stop of a rafter might be bodily closer to which of the subsequent parts of the roof?
Soffit
three a couple of preference options
When the sun panel gadget arrives on website, which items need to be stored near the work
location because they may be set up first.
Mounting hardware
3 a couple of choice options
Ladders used to get right of entry to a roof need to amplify at least how a long way above the
floor of the roof?
36" (3')
2 a couple of preference options
For electrical safety how many ft of clearance is want for most PV device?
3' (36")
3 more than one choice options
When getting ready to install a QuickMountPV anchor from Unirac what size pilot hollow need to
be drilled to get the anchor bolt or screw started out?
1/four"
3 more than one choice options
The use of PV cord and cable as conductors of PV power is addressed in
NEC Section 690.35
, 3 a couple of preference alternatives
When marking rafters don't forget that their part is much less than
2" thick
3 a couple of choice options
When splicing beams the use of CLICKSYStm beams and attachments from UNIRAC the nuts
and bolts have to be tightened to
10 ft. Lbs.
3 multiple preference options
UNIRAC beams should be mounted in spans not to exceed
36"
3 a couple of preference alternatives
The output of a combiner is usually fed right into a(n)
DC disconnect transfer
three multiple preference options
As an FLA battery is charging its temperature must by no means exceed
115 degrees Fahrenheit
3 multiple desire options
A Square D disconnect with a switch nameplate of 30A may have a DC score of
20A consistent with pole
3 a couple of preference options
When terminating the PV+ twine to the PV+ terminal inside an Outback FLEXmax 60 rate
controller the PV+ lug ought to be tightened to
35 in. Lbs.
Three multiple preference alternatives
When wiring in a Sunny Boy 3000US inverter it have to be tied to the
AC circuit breaker
three more than one preference options
Inspection (Module 4 Review)
True or False? Some of the maximum vital matters to check when preparing for a solar panel
set up activity are the building allows
True
1 more than one choice alternative
The low stop of a rafter might be bodily closer to which of the subsequent parts of the roof?
Soffit
three a couple of preference options
When the sun panel gadget arrives on website, which items need to be stored near the work
location because they may be set up first.
Mounting hardware
3 a couple of choice options
Ladders used to get right of entry to a roof need to amplify at least how a long way above the
floor of the roof?
36" (3')
2 a couple of preference options
For electrical safety how many ft of clearance is want for most PV device?
3' (36")
3 more than one choice options
When getting ready to install a QuickMountPV anchor from Unirac what size pilot hollow need to
be drilled to get the anchor bolt or screw started out?
1/four"
3 more than one choice options
The use of PV cord and cable as conductors of PV power is addressed in
NEC Section 690.35
, 3 a couple of preference alternatives
When marking rafters don't forget that their part is much less than
2" thick
3 a couple of choice options
When splicing beams the use of CLICKSYStm beams and attachments from UNIRAC the nuts
and bolts have to be tightened to
10 ft. Lbs.
3 multiple preference options
UNIRAC beams should be mounted in spans not to exceed
36"
3 a couple of preference alternatives
The output of a combiner is usually fed right into a(n)
DC disconnect transfer
three multiple preference options
As an FLA battery is charging its temperature must by no means exceed
115 degrees Fahrenheit
3 multiple desire options
A Square D disconnect with a switch nameplate of 30A may have a DC score of
20A consistent with pole
3 a couple of preference options
When terminating the PV+ twine to the PV+ terminal inside an Outback FLEXmax 60 rate
controller the PV+ lug ought to be tightened to
35 in. Lbs.
Three multiple preference alternatives
When wiring in a Sunny Boy 3000US inverter it have to be tied to the
AC circuit breaker
three more than one preference options
