Module 00104 Introduction to Power
Tools Exam 2025 Questions and
Answers
When using power tools, never engage the ________. - --Answer --Trigger
lock
Before replacing parts such as bits blades, or discs on any tool, you must
________. - --Answer --Disconnect the power source
Most hammer drills will not hammer until pressure is ________. - --
Answer --Applied to the drill bit
A pneumatic drill is commonly used ________. - --Answer --When there is
no source of electricity
Never use a circular saw that does not have an upper blade guard because the
________. - --Answer --Guard protects you from touching the blade
When using a circular saw, be sure to cut on the waste side of the cut mark to
allow for the blade's ________. - --Answer --Kerf
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 1
, Saws with fine blades that are excellent for delicate and intricate cutting are called
________. - --Answer --Saber saw
Before you plug any saw into a power source, make sure the ________. - --
Answer --Power switch is in the OFF position
A saw that has a thin, one-piece blade that runs around guides at either end of the
saw is a ________. - --Answer --Bandsaw
A power miter saw combines a miter box with a ________. - --Answer --
Circular saw
An angle grinder is used to grind ________. - --Answer --Hard, heavy
materials
The adjustable tool rest on a bench grinder should be positioned ________. - --
Answer --1/8 inch from the grinding wheel
A good way to check the condition of the grinding wheel on a bench grinder is to
________. - --Answer --Perform a ring test on the wheel
A grinder can catch on rough material edges and shift around, especially when
using rotary bits called ________. - --Answer --Burr bits
A low-velocity fastening system that is used to drive steel pins or threaded studs
into masonry and steel is a(n) ________. - --Answer --Powder-actuated tool
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 2
Tools Exam 2025 Questions and
Answers
When using power tools, never engage the ________. - --Answer --Trigger
lock
Before replacing parts such as bits blades, or discs on any tool, you must
________. - --Answer --Disconnect the power source
Most hammer drills will not hammer until pressure is ________. - --
Answer --Applied to the drill bit
A pneumatic drill is commonly used ________. - --Answer --When there is
no source of electricity
Never use a circular saw that does not have an upper blade guard because the
________. - --Answer --Guard protects you from touching the blade
When using a circular saw, be sure to cut on the waste side of the cut mark to
allow for the blade's ________. - --Answer --Kerf
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 1
, Saws with fine blades that are excellent for delicate and intricate cutting are called
________. - --Answer --Saber saw
Before you plug any saw into a power source, make sure the ________. - --
Answer --Power switch is in the OFF position
A saw that has a thin, one-piece blade that runs around guides at either end of the
saw is a ________. - --Answer --Bandsaw
A power miter saw combines a miter box with a ________. - --Answer --
Circular saw
An angle grinder is used to grind ________. - --Answer --Hard, heavy
materials
The adjustable tool rest on a bench grinder should be positioned ________. - --
Answer --1/8 inch from the grinding wheel
A good way to check the condition of the grinding wheel on a bench grinder is to
________. - --Answer --Perform a ring test on the wheel
A grinder can catch on rough material edges and shift around, especially when
using rotary bits called ________. - --Answer --Burr bits
A low-velocity fastening system that is used to drive steel pins or threaded studs
into masonry and steel is a(n) ________. - --Answer --Powder-actuated tool
....COPYRIGHT ©️ 2025 ALL RIGHTS RESERVED...TRUSTED & VERIFIED 2
