ARCH 331 MIDTERM TEST QUESTIONS WITH CORRECT ANSWERS FULLY SOLVED

ARCH 331 MIDTERM TEST QUESTIONS WITH CORRECT ANSWERS FULLY SOLVED Football Stadium: What is the typical material specification for W-shapes (hint reference General Notes)? - Answers ASTM A992 Structural Steel Church Facility - Steel Building - What is the size of the column at G/5? - Answers W10x60 Structural Steel Church Facility - Steel Building - How many and what size vertical reinforcement is required in a 30/54 belled (drilled and undereamed) pier? - Answers (5) - #6 Structural Steel Church Facility - What is the height that column G/5 terminates (top of column)? - Answers 26'-6" Post tensioned flat plate - per the title block, these sheets were issued "For Construction" since they are sealed - Answers False Emergency Medical Services Building & Structural Steel Weld Symbols - What type of weld is most nearly required for the bent beam per detail 4/S4.01 - Answers Bevel - CJP Metal Building System - What size (diameter) anchor rods and how many are required for column B/3? - Answers (4) - 3/4" Metal Building System - What is the roof pitch (slope) for the building? - Answers 4 on 12 Metal Building System - What is the typical purlin size between grids 5 and 6? - Answers 10x25Z14 Football Stadium - What is the total thickness of the composite slab at the Mezzanine level (Sheet S2.42)? - Answers 6 1/2" Football Stadium - How many and what size bottom bars are required for the cantilever raker just above the column, reference 15/S6.40? - Answers (6) - #9 Concrete Tilt Wall - What is the typical panel reinforcement required in a panel without openings? - Answers #4 @ 12 on-center, each way located in center of wall Concrete Tilt Wall - What size continuous angle is required at the top of the tilt wall panels to connect the roof joists to the panels? (Reference Sheet S3-1) - Answers L3x3x1/4 Specifications - Concrete Forming and Accessories can be found in which division section of the specifications "Project Manual"? - Answers 03 1000 What grade of steel are the steel channels shown on S1.1? - Answers ASTM A36 The type of steel roof specified is most nearly... - Answers 1.5B At the roof corners (ref S0.0 Components and Cladding Zones), the roof deck requires how many fasteners per 36" wide panel of roof deck? - Answers 7 The roof design assumed what maximum rainwater ponding on the roof (note effects the design of the drains and scupper). - Answers 4" On S1.1 along Grid C, from grid 4 to approximately 30' west, what is the thickness of the embed plate that connected the channels to the top of the CMU wall as they extend over? - Answers 3/4" What is the depth of the Typical Grade Beam on S1.0? - Answers 32" What is the size of the steel column at the Pay Station Canopy? - Answers W8x58 What is the depth (thickness) of spread footing type F1 supporting the canopy columns? - Answers 12" What is the size of the bottom chord of the trusses at the High Roof? - Answers HSS6x6x1/4 Which direction is the Low Roof sloping? - Answers South Which direction is the High Roof sloping? - Answers East What is the size of the steel angle supporting the roof deck where it ties into the CMU wall on the East Exterior wall? - Answers L4x3X5/16 The type of anchor used to fasten the deck angle in detail 12/S6.1 is what type of anchor? (Reference 6/S3.0) - Answers Screw Anchor What is the depth of the cold-formed steel purlins supporting the high roof deck? - Answers 6" What is the slope of the high roof? - Answers 3:12 What is the slope of the low roof between Grids A and B? - Answers 1/2:12 The requirements for the building foundation will most likely be found on which sheet in a drawing set? - Answers S101 Construction Documents = Drawings + Construction Contract + ... - Answers Specifications The General Notes sheets are generally located at the beginning of the sheet set - Answers True All of the following effect the magnitude of wind loads on buildings except. - Answers Weight of the building Earthquake induced forces is an example of lateral loading on a structure - Answers True Per the International Building Code, a fire station is required to be designed as what Risk Category? - Answers IV The exposure category (wind design) for Francis Hall is most nearly... - Answers Exposure B A structure design to the minimum requirements of the building code should not collapse when subjected to a minimum design earthquake or wind event - Answers True A structure designed and constructed to the minimum requirements of the building should not sustain structural damage during design earthquake or wind event - Answers False Earthquake forces are a function of the building mass (weight) and stiffness, which means that