NEIEP 800 Final Exam
Hydro elevators in low rise applications do not need an _____ _____ room.
(Ans- overhead machine
Some advantages of hydros are lower equipment and building construction
costs because the load of a hydro is carried to the _____ where as the load
of a traction car is carried by the _____ _____.
(Ans- ground, building structure
When drilling the jack hole, the only proper way to determine if the hole is
plumb is to remove the drill stem and bit and use a _____ _____.
(Ans- Spider Bob
To plumb the hole, a spider bob is attached to a length of piano wire
suspended from as near as possible to the top of the _____ or from a fixed
point on the drill rig.
(Ans- Hoist way
When welding a joint, lay _____ inch tack welds _____ degrees apart, shift
it 90 degrees and lay two more 1 inch tack welds 180 degrees apart.
(Ans- 1, 180
On power units having the motor beneath the tank, the pump may be either
_____ driven or _____ coupled.
(Ans- belt, direct
The purpose of the _____/_____ is to silence the effect of any pulsations in
the pump output and should be as close to the pump as possible.
(Ans- silencer, muffler
On Bolsters/Bolster Assembly, the plunger is fastened to the _____ _____
which is then mounted to the center of the Bolster Assembly.
(Ans- platen plate
, With wye-delta, reduced current starting is accomplished without the need
for _____.
(Ans- resistors
_____ run buttons should run the platform and sling at leveling speeds
only.
(Ans- Temporary
A _____ _____ consists of a piston held closed by an adjustable spring and
must open at a certain pressure to prevent any further increase in pressure.
(Ans- relief valve
A _____ lowering valve allows the car to be lowered at a speed not
exceeding 20fpm in case of power failure.
(Ans- manual
As the oil temperature changes, the _____ will change as well and will
effect the performance, more specifically, the leveling and approach of the
elevator.
(Ans- viscosity
Be sure well ways are properly _____ to avoid accidental injury to you, your
team or anyone working outside of our industry.
(Ans- barricaded
Barricades around the well way must be _____ inches high and be capable
of withstanding a _____lb force.
(Ans- 42, 200
A _____ protects you if you come in contact with a hot wire or component
and then come in contact with ground. It opens the circuit and diverts the
supplied current to ground.
(Ans- GFCI
Hydro elevators in low rise applications do not need an _____ _____ room.
(Ans- overhead machine
Some advantages of hydros are lower equipment and building construction
costs because the load of a hydro is carried to the _____ where as the load
of a traction car is carried by the _____ _____.
(Ans- ground, building structure
When drilling the jack hole, the only proper way to determine if the hole is
plumb is to remove the drill stem and bit and use a _____ _____.
(Ans- Spider Bob
To plumb the hole, a spider bob is attached to a length of piano wire
suspended from as near as possible to the top of the _____ or from a fixed
point on the drill rig.
(Ans- Hoist way
When welding a joint, lay _____ inch tack welds _____ degrees apart, shift
it 90 degrees and lay two more 1 inch tack welds 180 degrees apart.
(Ans- 1, 180
On power units having the motor beneath the tank, the pump may be either
_____ driven or _____ coupled.
(Ans- belt, direct
The purpose of the _____/_____ is to silence the effect of any pulsations in
the pump output and should be as close to the pump as possible.
(Ans- silencer, muffler
On Bolsters/Bolster Assembly, the plunger is fastened to the _____ _____
which is then mounted to the center of the Bolster Assembly.
(Ans- platen plate
, With wye-delta, reduced current starting is accomplished without the need
for _____.
(Ans- resistors
_____ run buttons should run the platform and sling at leveling speeds
only.
(Ans- Temporary
A _____ _____ consists of a piston held closed by an adjustable spring and
must open at a certain pressure to prevent any further increase in pressure.
(Ans- relief valve
A _____ lowering valve allows the car to be lowered at a speed not
exceeding 20fpm in case of power failure.
(Ans- manual
As the oil temperature changes, the _____ will change as well and will
effect the performance, more specifically, the leveling and approach of the
elevator.
(Ans- viscosity
Be sure well ways are properly _____ to avoid accidental injury to you, your
team or anyone working outside of our industry.
(Ans- barricaded
Barricades around the well way must be _____ inches high and be capable
of withstanding a _____lb force.
(Ans- 42, 200
A _____ protects you if you come in contact with a hot wire or component
and then come in contact with ground. It opens the circuit and diverts the
supplied current to ground.
(Ans- GFCI
