CWB 47.1 Exam Questions & Answers
100% Correct
CSA Standard W47.1 provides the requirements that must be met and adhered to by a company seeking
certification.
True or False? - ANSWER-True
Certification can be considered as an approval of the products fabricated by a
certificated company?
True or false?! - ANSWER-False
What are the duties of the welding engineer?
A) Provide engineering support to the company as required.
B) Development of new welding procedures
C) Periodic reviews of the company's welding practices
D) preparation of WPSs and WPDSs
E) all of the above - ANSWER-E
A welding supervisor with two years of fabrication experience is acceptable for division
1 company?
True or false? - ANSWER-False
Each supervisor shall have knowledge of?
A) weld faults
B) Quality control
C) Estimating
D) both a & c pertaining to directly related to their work. - ANSWER-D
What does "class" refer to?
A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel.
B) Electrode groups
C) a category of welder qualification, e.g., F, H,V or O welding position
D) Fillet and groove we'd combined test plate assemblies - ANSWER-C
What does classification refer to?
A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel.
B) Electrode groups
C) a category of welder qualification, e.g., F, H,V or O welding position
D) Fillet and groove we'd combined test plate assemblies - ANSWER-A
, What organization administer CSA Standard W47.1
A) there is no administrator
B) Canadian standards association
C) Canadian welding bureau - ANSWER-C
The Canadian welding bureau can withdraw a company's certification if the company is
NOT following the requirements of CSA standard W47.1
True or false ? - ANSWER-True
How many divisions of certification are specified in CSA Standard W47.1 ?
A) one
B) two
C) three
D) four - ANSWER-C
Is a company certified in division 1 required to employ a full time or retain a part time
welding engineer?
A) retain a part time welding engineer
B) employ a full time welding engineer
C) no engineer is required
D) employ a full time welding inspector only - ANSWER-B
Is a company certified in division 3 required to employ a full time or retain a part time
welding engineer?
A) Employ a full time welding engineer
B) Retain a part time welding engineer
C) retain a part time welding engineer responsible to the company only for welding
procedures and practice
D) No welding engineer is required - ANSWER-D
CSA Standard W47.1 requires each designated plant, shop or section to meet the
requirements of certification within this standard with respect to welders, welding
procedures specification, welding procedure data sheets, welding supervisor and
welding engineer, where applicable
True or false? - ANSWER-True
A company doing only erection work involving welding must have a pony in order to be
certified to CSA standard W47.1
True or false? - ANSWER-False
When must the company inform the Canadian bureau of any loss or change in welding
engineering or supervisory personnel?
A) immediately
B) after 3 months
C) after 6 months
100% Correct
CSA Standard W47.1 provides the requirements that must be met and adhered to by a company seeking
certification.
True or False? - ANSWER-True
Certification can be considered as an approval of the products fabricated by a
certificated company?
True or false?! - ANSWER-False
What are the duties of the welding engineer?
A) Provide engineering support to the company as required.
B) Development of new welding procedures
C) Periodic reviews of the company's welding practices
D) preparation of WPSs and WPDSs
E) all of the above - ANSWER-E
A welding supervisor with two years of fabrication experience is acceptable for division
1 company?
True or false? - ANSWER-False
Each supervisor shall have knowledge of?
A) weld faults
B) Quality control
C) Estimating
D) both a & c pertaining to directly related to their work. - ANSWER-D
What does "class" refer to?
A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel.
B) Electrode groups
C) a category of welder qualification, e.g., F, H,V or O welding position
D) Fillet and groove we'd combined test plate assemblies - ANSWER-C
What does classification refer to?
A) "T", "S", "FW", "ASW" or "WT" designation of welding personnel.
B) Electrode groups
C) a category of welder qualification, e.g., F, H,V or O welding position
D) Fillet and groove we'd combined test plate assemblies - ANSWER-A
, What organization administer CSA Standard W47.1
A) there is no administrator
B) Canadian standards association
C) Canadian welding bureau - ANSWER-C
The Canadian welding bureau can withdraw a company's certification if the company is
NOT following the requirements of CSA standard W47.1
True or false ? - ANSWER-True
How many divisions of certification are specified in CSA Standard W47.1 ?
A) one
B) two
C) three
D) four - ANSWER-C
Is a company certified in division 1 required to employ a full time or retain a part time
welding engineer?
A) retain a part time welding engineer
B) employ a full time welding engineer
C) no engineer is required
D) employ a full time welding inspector only - ANSWER-B
Is a company certified in division 3 required to employ a full time or retain a part time
welding engineer?
A) Employ a full time welding engineer
B) Retain a part time welding engineer
C) retain a part time welding engineer responsible to the company only for welding
procedures and practice
D) No welding engineer is required - ANSWER-D
CSA Standard W47.1 requires each designated plant, shop or section to meet the
requirements of certification within this standard with respect to welders, welding
procedures specification, welding procedure data sheets, welding supervisor and
welding engineer, where applicable
True or false? - ANSWER-True
A company doing only erection work involving welding must have a pony in order to be
certified to CSA standard W47.1
True or false? - ANSWER-False
When must the company inform the Canadian bureau of any loss or change in welding
engineering or supervisory personnel?
A) immediately
B) after 3 months
C) after 6 months
