IMSA Traffic Signal Technician II EXAM STUDY GUIDE 2026/2027 ACCURATE QUESTIONS WITH CORRECT DETAILED ANSWERS || 100% GUARANTEED PASS <RECENT VERSION>

IMSA Traffic Signal Technician II EXAM STUDY GUIDE 2026/2027 ACCURATE QUESTIONS WITH CORRECT DETAILED ANSWERS || 100% GUARANTEED PASS &lt;RECENT VERSION&gt; 1. In a TS2 cabinet, how many times can the MMU experience a "Port 1 Fail" in a 24 hour period before the fault is latched? - ANSWER 1 2. On a 2070 MMU monitor unit, how does the field tech program allowable phases? - ANSWER Remove diode on program card for allowable phases 3. On an MMU, is it possible to tape the reset button to prevent the traffic signal from going into flash? - ANSWER Yes, it by-passes the conflict feature and will not flash 4. On a NEMA CMU program card, how does the signal tech program allowable phases? - ANSWER Install copper jumpers and soldering them on the program card 5. According to best maintenance practices, how often should CMU/MMU be tested? - ANSWER Annually 6. The MMU indicates a RED-FAIL fault on phase 6. Why? - ANSWER The load switch/switch pack produces no outputs. 7. The purpose of the controller CVM (Controller Voltage Monitor) output is to allow the CMU/MMU to monitor the - ANSWER Controller health 8. When a Technician is recertifying the CMU/MMU at an intersection, what should the technician do to have the intersection exit flash? - ANSWER Replace the CMU/MMU with a newly tested unit 9. Absence of all colors on a load switch will be indicated by what fault on an MMU or MMU2? - ANSWER Red Fail 10. BIU - ANSWER bus interface unit 11. 8 Channel and 16 channel chassis, are supported 4 racks 4- 8 - 12 bays & 16 - channel configurations. - ANSWER TS-2 12. TS2 connectors are what connector? - ANSWER serial connectors 13. TS - 2 BIS interface reduces WHAT? - ANSWER the complexity of the controller cabinet and Hundreds of conductors 14. NTCIP - ANSWER the national transportation Communications for, intelligent protocol 15. NTCIP - ANSWER to accommodate subsystems and users OF (ITS) 16. SDLC - ANSWER synchronous data Link Communications 17. A (. ) fault, will stay until the monitor is reset - ANSWER a latching fault 18. a blank will return to its state once the power is restored to the system - ANSWER non latching fault 19. these are primary functions of phasing conflicts, absence of red on a phase and proper operating DC voltage. On what monitors? - ANSWER CMU & MMU 20. examples of unlatching and latching Faults Are - ANSWER low voltage, voltage drop, loss of 24 volt power supply. 21. load switches 1 through 6 - ANSWER 1. AC hot 2. ground, 3. red / don't walk output to indication 4. N/U 5. Yellow PED CRL /OUTPUT INDICATION 6. RED/ INPUT FROM CONTROLLER 22. Load switches 7-12 - ANSWER 7. Grn / output to indication 8. Y PED CRL / input to controller 9. 24 V 10. Grn Walk/ input to controller 11. AC NEUTRAL 12.NOT USED 23. The traffic field technician is responsible for performing what types of maintenance on signals? - ANSWER Preventive and Emergency 24. The single most important focus for the traffic signal field technician is? - ANSWER Safety 25. Three main categories of safety a traffic signal technician is responsible for? - ANSWER Safety of motorist and pedestrians His or her own personal safety Safety of public and personal property 26. Traffic signal field technicians perform several maintenance and repair functions above the ground and roadway typically using what two vehicles? - ANSWER Bucket Truck Aerial lift (platform truck) 27. While using a bucket truck or aerial lift what implement provides proper protection for the user? - ANSWER Protective Harness 28. What responsibilities (liability) does a Traffic signal technician have while involved in repair, testing or maintenance? - ANSWER Legal liability Dealing with the public 29. It is imperative that the traffic signal field technician maintain comprehensive what of all the steps taken during repair and maintenance of traffic signals? - ANSWER Documentation 30. What two instances are documentation required for a traffic signal field technician? - ANSWER Routine maintenance Emergency repair 31. Approved Product List - ANSWER Contractor need not provide submittals if using materials on this list, a certification must be provided instead. 32. Certification number - ANSWER Number given to a product that has been pre-approved. Often it must be permanently engraved or stenciled on the product. 33. Shop-Drawing Submittals - ANSWER Most items of a structural nature require this to be submitted and provide detailed information. Usually sealed by and engineer. 34. Factory Acceptance Testing - ANSWER Tests conducted at the equipment suppliers facility. 35. Stockpiled Materials - ANSWER Materials kept at the contractor's warehouse or yard. Partial payments may be granted. 36. Inspector recordkeeping responsibilities - ANSWER 1. Daily construction activities 2. Federal compliance forms 3. Testing result forms 4. Quantities installed 5. Photographs 6. Final inspection report