2025 MKC SWE Study 2025 NEWEST
EXAM COMPLETE 110 QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) ALREADY GRADED A+ BRAND
NEW!!
P100 dipstick location - ,,,,answer,,,..2 dipsticks on each side of the
engine
P100 engine specification - ,,,,answer,,,..Yanmar L100AE/EE air cooled,
single cylinder, 4 stroke, diesel F-76 or JP-5
P100 Specifications - ,,,,answer,,,..164lbs of wet weight, 1.45 Gallons of
fuel 2.75 hrs of run time 100GPM@83PSI@20ft lift, packing screw 6" long
9/16 wrench, drip rate 5-50 DPM
Securing P100 - ,,,,answer,,,..turn speed to low, run with no load for aprox
5 minutes to allow it to cool off
P6 Specs - ,,,,answer,,,..Honda GX200, 6.5HP, 3Gal tank, 4hour run time,
86 octane gas,unit 60lbs, kit 120lbs
P6 Dry run time - ,,,,answer,,,..This pump is equipped with a mechanical
lip seal. Avoid running the pump dry or at high speed if there is no
discharge water. If there is no discharge flow after two minutes, shut
down the engine and check for leaks in the suction hose
, P6 Maintenance - ,,,,answer,,,..• Automotive 4 stroke SAE 10W-30
detergent oil is recommended for the engine for general operation. See
the Honda GX200 Engine Owner's Manual for oil recommendations for
adverse operating conditions. • Check the engine oil level prior to each
use. Add oil as necessary. • Change the engine oil after the first 20 hours;
then every 100 hours, or 6 months thereafter. • Replace the inline fuel
filter after the first 20 hours; then every 100 hours, or 6 months thereafter.
P6 time between fuel tank changes - ,,,,answer,,,..30 seconds
P6 securing - ,,,,answer,,,..1. Return the throttle to the "IDLE" position. 2.
Close the fuel valve by pushing it to the left to the "OFF" position. 3. Shut
down the engine by turning the ignition switch counter clockwise to the
"OFF" position
P6 Fittings - ,,,,answer,,,..15' 3" dia camlock rigid suction hose with
strainer, 20' 3" dia camlock fiber reinforced flexible hose 250GPM@12' lift
@3900RPM, Set the throttle about 1/3 open.,
P6 speeds - ,,,,answer,,,..Idle 1400 full throttle 3900
Pressure gauge and transducer calibration interval - ,,,,answer,,,..24
months
Meter calibration interval - ,,,,answer,,,..24 months
Temperature gauges calibration interval - ,,,,answer,,,..36 months
Pressure gauges in weapons spaces - ,,,,answer,,,..12 month
Out of calibration label - ,,,,answer,,,..Orange in color, error is small and
consistent
EXAM COMPLETE 110 QUESTIONS AND
CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) ALREADY GRADED A+ BRAND
NEW!!
P100 dipstick location - ,,,,answer,,,..2 dipsticks on each side of the
engine
P100 engine specification - ,,,,answer,,,..Yanmar L100AE/EE air cooled,
single cylinder, 4 stroke, diesel F-76 or JP-5
P100 Specifications - ,,,,answer,,,..164lbs of wet weight, 1.45 Gallons of
fuel 2.75 hrs of run time 100GPM@83PSI@20ft lift, packing screw 6" long
9/16 wrench, drip rate 5-50 DPM
Securing P100 - ,,,,answer,,,..turn speed to low, run with no load for aprox
5 minutes to allow it to cool off
P6 Specs - ,,,,answer,,,..Honda GX200, 6.5HP, 3Gal tank, 4hour run time,
86 octane gas,unit 60lbs, kit 120lbs
P6 Dry run time - ,,,,answer,,,..This pump is equipped with a mechanical
lip seal. Avoid running the pump dry or at high speed if there is no
discharge water. If there is no discharge flow after two minutes, shut
down the engine and check for leaks in the suction hose
, P6 Maintenance - ,,,,answer,,,..• Automotive 4 stroke SAE 10W-30
detergent oil is recommended for the engine for general operation. See
the Honda GX200 Engine Owner's Manual for oil recommendations for
adverse operating conditions. • Check the engine oil level prior to each
use. Add oil as necessary. • Change the engine oil after the first 20 hours;
then every 100 hours, or 6 months thereafter. • Replace the inline fuel
filter after the first 20 hours; then every 100 hours, or 6 months thereafter.
P6 time between fuel tank changes - ,,,,answer,,,..30 seconds
P6 securing - ,,,,answer,,,..1. Return the throttle to the "IDLE" position. 2.
Close the fuel valve by pushing it to the left to the "OFF" position. 3. Shut
down the engine by turning the ignition switch counter clockwise to the
"OFF" position
P6 Fittings - ,,,,answer,,,..15' 3" dia camlock rigid suction hose with
strainer, 20' 3" dia camlock fiber reinforced flexible hose 250GPM@12' lift
@3900RPM, Set the throttle about 1/3 open.,
P6 speeds - ,,,,answer,,,..Idle 1400 full throttle 3900
Pressure gauge and transducer calibration interval - ,,,,answer,,,..24
months
Meter calibration interval - ,,,,answer,,,..24 months
Temperature gauges calibration interval - ,,,,answer,,,..36 months
Pressure gauges in weapons spaces - ,,,,answer,,,..12 month
Out of calibration label - ,,,,answer,,,..Orange in color, error is small and
consistent
