API 510 Practice Test (Referenced) Review with
Compete Solutions
Substituting NDE procedures for a pressure test tapping or welding on in-service equipment
after major repair may be done only after: should include:
API 510 5.8.8.1 - -The engineer and API 577 11.2.5 - -Positive Metal
inspector have approved. Identification (PMI)
An example of vessels not covered by API 510 Any repair welding should be performed
are: according to a procedure accepted by the:
API 510 1.1.1 - -Vessels officially retired API 510 8.1.1 - -Inspector or Engineer
from service and abandoned in place.
Welding of carbon steel with carbon contents
ACFM is an acronym for: over 0.30%
ASME SEC 5 Article 15 - -Alternating API 510 8.1.5 - -May need special attention
Current Field Measurement and preheating to avoid weld cracking.
A pneumatic testing precedure should be Inspector recommendations can be changed or
developed by whom before conducting the test? deleted after review by whom?
API 510 5.8.6 - -Engineer API 510 6.9 - -Pressure Vessel Engineer or
Inspection
Supervision
A signal of discontinuity in the material under
nondestructive examination is considered:
API RP 577 3.1.36 - -Indication Deposited weld metal on the face of a weld
preparation or surface that will be part of a
welded
In what type of service should vessels be joint is referred to as:
evaluated for potential fatigue cracking failures API 577 3.1.14 - -Buttering
and have appropriate inspections planned?
API 510 5.4.4 - -Cyclic Service
Which type of ultrasonic display shows the
amplitude of the signal coming from the
Corrosion and other damage identified during discontinuity as a function of time?
inspections and examinations must be API 577 9.9.2.1 - -A-scan Display
characterized, sized, and evaluated per Section
7 (Inspection Data Evaluation, Analysis, and
Recording) with deviations from the inspection Flame-sprayed aluminum coatings have been
plan being approved by whom? used on carbon steels to prevent what damage
API 510 5.5.1 - -Inspector or Engineer mechanism?
API 571 4.3.3.6 - -Corrosion Under
Insulation
Inspection tasks typically associated with hot
1/4
Compete Solutions
Substituting NDE procedures for a pressure test tapping or welding on in-service equipment
after major repair may be done only after: should include:
API 510 5.8.8.1 - -The engineer and API 577 11.2.5 - -Positive Metal
inspector have approved. Identification (PMI)
An example of vessels not covered by API 510 Any repair welding should be performed
are: according to a procedure accepted by the:
API 510 1.1.1 - -Vessels officially retired API 510 8.1.1 - -Inspector or Engineer
from service and abandoned in place.
Welding of carbon steel with carbon contents
ACFM is an acronym for: over 0.30%
ASME SEC 5 Article 15 - -Alternating API 510 8.1.5 - -May need special attention
Current Field Measurement and preheating to avoid weld cracking.
A pneumatic testing precedure should be Inspector recommendations can be changed or
developed by whom before conducting the test? deleted after review by whom?
API 510 5.8.6 - -Engineer API 510 6.9 - -Pressure Vessel Engineer or
Inspection
Supervision
A signal of discontinuity in the material under
nondestructive examination is considered:
API RP 577 3.1.36 - -Indication Deposited weld metal on the face of a weld
preparation or surface that will be part of a
welded
In what type of service should vessels be joint is referred to as:
evaluated for potential fatigue cracking failures API 577 3.1.14 - -Buttering
and have appropriate inspections planned?
API 510 5.4.4 - -Cyclic Service
Which type of ultrasonic display shows the
amplitude of the signal coming from the
Corrosion and other damage identified during discontinuity as a function of time?
inspections and examinations must be API 577 9.9.2.1 - -A-scan Display
characterized, sized, and evaluated per Section
7 (Inspection Data Evaluation, Analysis, and
Recording) with deviations from the inspection Flame-sprayed aluminum coatings have been
plan being approved by whom? used on carbon steels to prevent what damage
API 510 5.5.1 - -Inspector or Engineer mechanism?
API 571 4.3.3.6 - -Corrosion Under
Insulation
Inspection tasks typically associated with hot
1/4
