100% CORRECT WELL DETAILED
ANSWERS|LATEST
UPDATE!!!!2025/2026|GUARANTEED
A hard hat is required on a job site when _____?
OSHA - ANSWER There is a danger from falling objects
Any condition occurring in a communications or transmission channel that interferes with
the proper transmission or interpretation or both of status change signals at the supervising
station is known as _____?
NFPA 72-3.3.9 - ANSWER Adverse condition
A 4"x 4" box has multiple FPL cables pulled through it. A minimum of _____ inches of cable
should be available for splicing?
NFPA 70-300.14 - ANSWER 6
Wiring installed underneath a corrugated metal roof shall maintain a minimum separation of
_____ inches?
NFPA 70-300.4(E ) - ANSWER 1.5
According to NFPA 72, the system account number is located in section _____ of the record
of completion?
NFPA 72-Figure 7.8.2(a) - ANSWER 2
Consider a circuit with a resistance of 6 ohms and a current of 2 amperes. What is the
voltage? - ANSWER 12 volts
1
, All means of interconnecting equipment, devices, and appliances, and wiring connections
shall be monitored for the integrity of the interconnecting conductors or equivalent so that
the occurrence of a single open or a single ground fault condition in the installation
conductors or other signaling channels is automatically indicated within _____ seconds?
NFPA 72-12.6.1 - ANSWER 200
Pathway survivability level _____ shall consist of pathways and buildings that are fully
protected by an automatic sprinkler system with 2 hour fire rated circuit integrity cable?
NFPA 72-12.4.4 - ANSWER 3
What is the minimum conductor size for Power Limited Fire Alarm cable which is single
conductor?
NFPA 70-760.179(B) - ANSWER 18 AWG
According to NFPA 72, the maximum flash rate for a visible notification appliance shall not
exceed _____ flashes per second?
NFPA 72-18.5.3.1 - ANSWER 2
Consider the installation of rigid metal conduit. Where conduit is threaded in the field, a
standard cutting die with a 1 in _____ taper shall be used?
NFPA 70-344-.28 - ANSWER 16
According to NFPA 72, section _____ of the record of completion is used to note the input
voltage?
NFPA 72-Figure 7.8.2(a) - ANSWER 5.1.1
In order to determine the requirements for return side HVAC duct detectors _____ should be
consulted?
NFPA 72-17.7.6.3.1 - ANSWER NFPA 90A
2
ANSWERS|LATEST
UPDATE!!!!2025/2026|GUARANTEED
A hard hat is required on a job site when _____?
OSHA - ANSWER There is a danger from falling objects
Any condition occurring in a communications or transmission channel that interferes with
the proper transmission or interpretation or both of status change signals at the supervising
station is known as _____?
NFPA 72-3.3.9 - ANSWER Adverse condition
A 4"x 4" box has multiple FPL cables pulled through it. A minimum of _____ inches of cable
should be available for splicing?
NFPA 70-300.14 - ANSWER 6
Wiring installed underneath a corrugated metal roof shall maintain a minimum separation of
_____ inches?
NFPA 70-300.4(E ) - ANSWER 1.5
According to NFPA 72, the system account number is located in section _____ of the record
of completion?
NFPA 72-Figure 7.8.2(a) - ANSWER 2
Consider a circuit with a resistance of 6 ohms and a current of 2 amperes. What is the
voltage? - ANSWER 12 volts
1
, All means of interconnecting equipment, devices, and appliances, and wiring connections
shall be monitored for the integrity of the interconnecting conductors or equivalent so that
the occurrence of a single open or a single ground fault condition in the installation
conductors or other signaling channels is automatically indicated within _____ seconds?
NFPA 72-12.6.1 - ANSWER 200
Pathway survivability level _____ shall consist of pathways and buildings that are fully
protected by an automatic sprinkler system with 2 hour fire rated circuit integrity cable?
NFPA 72-12.4.4 - ANSWER 3
What is the minimum conductor size for Power Limited Fire Alarm cable which is single
conductor?
NFPA 70-760.179(B) - ANSWER 18 AWG
According to NFPA 72, the maximum flash rate for a visible notification appliance shall not
exceed _____ flashes per second?
NFPA 72-18.5.3.1 - ANSWER 2
Consider the installation of rigid metal conduit. Where conduit is threaded in the field, a
standard cutting die with a 1 in _____ taper shall be used?
NFPA 70-344-.28 - ANSWER 16
According to NFPA 72, section _____ of the record of completion is used to note the input
voltage?
NFPA 72-Figure 7.8.2(a) - ANSWER 5.1.1
In order to determine the requirements for return side HVAC duct detectors _____ should be
consulted?
NFPA 72-17.7.6.3.1 - ANSWER NFPA 90A
2
