Engineer Equipment Chief (MCIZ1328FZ) WITH 70
QUESTIONS AND ANSWERS NEWEST RATED A+
2026 UPDATED 100% VERIFIED CORRECT
Engineer Equipment Chief (MCIZ1328FZ) - 100 Questions &
Answers
1. What is the primary purpose of the Lubrication Order (LO)?
A) To schedule vehicle maintenance
B) To provide detailed lubrication instructions and intervals for
equipment
C) To order new lubricants and grease
D) To track fuel consumption
2. Which manual provides the Marine Corps' central policy for the
Maintenance Management Program (MMS)?
A) TM 4700-15/1
B) MCO 4790.2C
C) NAVMC 3500.59B
D) DA PAM 750-1
3. The Equipment Status Report (ESR) is submitted using which
form?
A) DD Form 1970
B) DD Form 3146
C) SF 91
D) NAVMC 10274
4. What does the acronym "PMCS" stand for?
A) Planned Maintenance and Corrective Services
B) Preventive Maintenance, Checks, and Services
,C) Periodic Material Condition Survey
D) Primary Maintenance Control System
5. Who is ultimately responsible for the maintenance and condition
of a unit's equipment?
A) The Equipment Chief
B) The Maintenance Chief
C) The Commanding Officer
D) The Logistics Officer
6. What is the first step in the troubleshooting process?
A) Isolate the problem
B) Perform a visual inspection
C) Consult the technical manual
D) Identify the complaint
7. A "C" condition code on an ESR indicates the equipment is:
A) Inoperable and not economically repairable
B) Inoperable, requires major repairs
C) Operable but needs minor repairs
D) Fully mission capable
8. The Maintenance Action Form (MAF) is primarily used to:
A) Order parts from supply
B) Document performed maintenance and repairs
C) Report a vehicle accident
D) Schedule operator training
9. What is the primary function of a hydraulic accumulator?
A) To filter hydraulic fluid
B) To store fluid under pressure
, C) To cool the hydraulic system
D) To regulate hydraulic pressure
10. Before performing any maintenance on a piece of equipment,
what is the most critical safety step?
A) Put on gloves
B) De-energize and lockout/tagout the equipment
C) Check the fluid levels
D) Clean the work area
11. Which component converts hydraulic pressure into linear
mechanical force?
A) Hydraulic pump
B) Control valve
C) Hydraulic cylinder
D) Orifice
12. The three main parts of a track assembly are the track shoes,
rollers, and what?
A) Sprockets
B) Brakes
C) Axles
D) Struts
13. What type of fire extinguisher is required for flammable liquid
fires (Class B)?
A) Pressurized Water
B) Carbon Dioxide (CO2) or Dry Chemical
C) Foam
D) Wet Chemical
QUESTIONS AND ANSWERS NEWEST RATED A+
2026 UPDATED 100% VERIFIED CORRECT
Engineer Equipment Chief (MCIZ1328FZ) - 100 Questions &
Answers
1. What is the primary purpose of the Lubrication Order (LO)?
A) To schedule vehicle maintenance
B) To provide detailed lubrication instructions and intervals for
equipment
C) To order new lubricants and grease
D) To track fuel consumption
2. Which manual provides the Marine Corps' central policy for the
Maintenance Management Program (MMS)?
A) TM 4700-15/1
B) MCO 4790.2C
C) NAVMC 3500.59B
D) DA PAM 750-1
3. The Equipment Status Report (ESR) is submitted using which
form?
A) DD Form 1970
B) DD Form 3146
C) SF 91
D) NAVMC 10274
4. What does the acronym "PMCS" stand for?
A) Planned Maintenance and Corrective Services
B) Preventive Maintenance, Checks, and Services
,C) Periodic Material Condition Survey
D) Primary Maintenance Control System
5. Who is ultimately responsible for the maintenance and condition
of a unit's equipment?
A) The Equipment Chief
B) The Maintenance Chief
C) The Commanding Officer
D) The Logistics Officer
6. What is the first step in the troubleshooting process?
A) Isolate the problem
B) Perform a visual inspection
C) Consult the technical manual
D) Identify the complaint
7. A "C" condition code on an ESR indicates the equipment is:
A) Inoperable and not economically repairable
B) Inoperable, requires major repairs
C) Operable but needs minor repairs
D) Fully mission capable
8. The Maintenance Action Form (MAF) is primarily used to:
A) Order parts from supply
B) Document performed maintenance and repairs
C) Report a vehicle accident
D) Schedule operator training
9. What is the primary function of a hydraulic accumulator?
A) To filter hydraulic fluid
B) To store fluid under pressure
, C) To cool the hydraulic system
D) To regulate hydraulic pressure
10. Before performing any maintenance on a piece of equipment,
what is the most critical safety step?
A) Put on gloves
B) De-energize and lockout/tagout the equipment
C) Check the fluid levels
D) Clean the work area
11. Which component converts hydraulic pressure into linear
mechanical force?
A) Hydraulic pump
B) Control valve
C) Hydraulic cylinder
D) Orifice
12. The three main parts of a track assembly are the track shoes,
rollers, and what?
A) Sprockets
B) Brakes
C) Axles
D) Struts
13. What type of fire extinguisher is required for flammable liquid
fires (Class B)?
A) Pressurized Water
B) Carbon Dioxide (CO2) or Dry Chemical
C) Foam
D) Wet Chemical
