PA Appraisers License Exam 2025/2026
Exam Questions with 100% Correct
Answers | Latest Update
How is a diamond condition fixed? - 🧠 ANSWER ✔✔By pulling the damage
for length. Diamond is a length condition
When measuring a unibody vehicle, it is discovered that the left front rail is
111mm from spec in width. What condition is this? - 🧠 ANSWER ✔✔Width
is calculated from the center out, so a value of -111mm on the left rail
shows sway to the right and in toward centerline
A collision-damaged vehicle is discovered to be down in height at the
opposite end of the center section. What condition is this frame in? - 🧠
ANSWER ✔✔Twist condition
,When diagnosing the damage to a full frame assembly on a sport utility
vehicle, it is determined that the left side frame rail is higher than the right
side frame rail. Technician A says the damaged state is known as a twist
condition. Technician B says a sway condition exists. Who is right? - 🧠
ANSWER ✔✔Tech A. When a frame rail's relationship to the vehicle
centerline is changed, such as pushed either to the left or
right, the condition is known as sway. "Twist" refers to the condition of the
frame when entire sections are driven higher or lower than the opposite
side.
Metal fillers contain different ingredients that provide fillers with special
properties. What benefit does fiberglass provide? - 🧠 ANSWER
✔✔Fiberglass offers more resistance to moisture
What does HSLA stand for? - 🧠 ANSWER ✔✔High Strength Low Alloy
When replacing the floor pan in the trunk area, what joint should be used to
join the new pan to the existing floor? - 🧠 ANSWER ✔✔Overlap joint
When acoustical foam is removed during the repair, what must happen
afterwards? - 🧠 ANSWER ✔✔Replace the acoustical foam
, When setting up a three-dimensional measuring system, it should be setup
on an undamaged area, and start with what section? - 🧠 ANSWER
✔✔Starting in the center section
What is the plastic Black box in rear of the car? - 🧠 ANSWER ✔✔Vapor
Canister
Grinding or squeaking from a wheel is a sign of what? - 🧠 ANSWER
✔✔Bad bearings
The insurance commissioner is responsible for everything except? - 🧠
ANSWER ✔✔Endorsing an Insurance Company
How do you tell when a ball joint is bad? - 🧠 ANSWER ✔✔Measure fixed
points from knuckle to rotor
What makes the windows go up and down? - 🧠 ANSWER ✔✔Window
regulator
What panel needs to get removed is there is damage to the quarter panel?
- 🧠 ANSWER ✔✔The taillight & bumper
What is an actuator? - 🧠 ANSWER ✔✔Tells something to do something
COPYRIGHT©PROFFKERRYMARTIN 2025/2026. YEAR PUBLISHED 2025. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE.
PRIVACY STATEMENT. ALL RIGHTS RESERVED
Exam Questions with 100% Correct
Answers | Latest Update
How is a diamond condition fixed? - 🧠 ANSWER ✔✔By pulling the damage
for length. Diamond is a length condition
When measuring a unibody vehicle, it is discovered that the left front rail is
111mm from spec in width. What condition is this? - 🧠 ANSWER ✔✔Width
is calculated from the center out, so a value of -111mm on the left rail
shows sway to the right and in toward centerline
A collision-damaged vehicle is discovered to be down in height at the
opposite end of the center section. What condition is this frame in? - 🧠
ANSWER ✔✔Twist condition
,When diagnosing the damage to a full frame assembly on a sport utility
vehicle, it is determined that the left side frame rail is higher than the right
side frame rail. Technician A says the damaged state is known as a twist
condition. Technician B says a sway condition exists. Who is right? - 🧠
ANSWER ✔✔Tech A. When a frame rail's relationship to the vehicle
centerline is changed, such as pushed either to the left or
right, the condition is known as sway. "Twist" refers to the condition of the
frame when entire sections are driven higher or lower than the opposite
side.
Metal fillers contain different ingredients that provide fillers with special
properties. What benefit does fiberglass provide? - 🧠 ANSWER
✔✔Fiberglass offers more resistance to moisture
What does HSLA stand for? - 🧠 ANSWER ✔✔High Strength Low Alloy
When replacing the floor pan in the trunk area, what joint should be used to
join the new pan to the existing floor? - 🧠 ANSWER ✔✔Overlap joint
When acoustical foam is removed during the repair, what must happen
afterwards? - 🧠 ANSWER ✔✔Replace the acoustical foam
, When setting up a three-dimensional measuring system, it should be setup
on an undamaged area, and start with what section? - 🧠 ANSWER
✔✔Starting in the center section
What is the plastic Black box in rear of the car? - 🧠 ANSWER ✔✔Vapor
Canister
Grinding or squeaking from a wheel is a sign of what? - 🧠 ANSWER
✔✔Bad bearings
The insurance commissioner is responsible for everything except? - 🧠
ANSWER ✔✔Endorsing an Insurance Company
How do you tell when a ball joint is bad? - 🧠 ANSWER ✔✔Measure fixed
points from knuckle to rotor
What makes the windows go up and down? - 🧠 ANSWER ✔✔Window
regulator
What panel needs to get removed is there is damage to the quarter panel?
- 🧠 ANSWER ✔✔The taillight & bumper
What is an actuator? - 🧠 ANSWER ✔✔Tells something to do something
COPYRIGHT©PROFFKERRYMARTIN 2025/2026. YEAR PUBLISHED 2025. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE.
PRIVACY STATEMENT. ALL RIGHTS RESERVED
