Class 200 NEIEP Final | 80 Quizzes with
Certified Solutions | 2025/2026 Edition
Verified Questions and Correct Answers | 100% Accurate | Graded A+
Introduction
This complete and certified resource covers the Class 200 NEIEP Final Exam along with 80
quizzes, featuring verified questions and correct solutions, fully updated for the 2025/2026
academic year. Designed to reflect current NEIEP standards, this compilation supports
mastery of key concepts for elevator mechanics and apprenticeship success.
Answer Format
Correct answers are marked in bold and green to ensure fast, effective, and accurate review.
Class 200 NEIEP Final Exam
Question 1: Which lay of wire rope has the strand wires in line with the rope axis?
A) Lang lay
B) Regular lay
C) Alternate lay
D) Reverse lay
Rationale: Regular lay has strand wires aligned with the rope axis, reducing wear.
Question 2: At what speed should counterweight safeties be set to trip?
A) Same as car governor
B) Up to 10% higher than car governor
C) 20% lower than car governor
D) Twice the car speed
Rationale: Counterweight safeties trip at up to 10% higher speed for safety margins.
Question 3: Which type of safety uses an oil buffer between the car and safety planks?
A) Type A
B) Type B
C) Type C
D) Type D
Rationale: Type B safeties use oil buffers to absorb impact.
Question 4: What is the minimum size wire allowed for 110VAC lighting circuits to elevator
cars?
A) 14 AWG
B) 12 AWG
C) 10 AWG
D) 16 AWG
Rationale: 12 AWG is the minimum for 110VAC lighting per code.
Question 5: What is the breaking strength for 1 1/8" nylon rope with a safety factor of 5?
A) 10,000 lbs
,B) 15,000 lbs
C) 20,000 lbs
D) 25,000 lbs
Rationale: Per Table 1, 1 1/8" nylon rope has a breaking strength of 15,000 lbs with a safety
factor of 5.
Question 6: What component engages the car door to the hoistway door during opening and
closing?
A) Door operator
B) Door clutch
C) Interlock
D) Retiring cam
Rationale: The door clutch couples car and hoistway doors for synchronized movement.
Question 7: How often must wires in high-rise raceways be supported?
A) Every 50 feet
B) Every 100 feet
C) Every 150 feet
D) Every 200 feet
Rationale: Code requires wire support every 100 feet in high-rise raceways.
Question 8: If voltage is present at the generator armature but not at the motor armature,
what is likely wrong?
A) Motor failure
B) Open loop circuit
C) Faulty governor
D) Broken sheave
Rationale: An open loop circuit prevents voltage transfer to the motor.
Question 9: How should passenger hoistway doors be stored?
A) Flat on the floor
B) Vertically on the long edge
C) Stacked horizontally
D) Leaning against a wall
Rationale: Vertical storage on the long edge prevents damage.
Question 10: What adjusts to reduce building compression effects on an elevator?
A) Governor ropes
B) Rail jack bolts
C) Door tracks
D) Counterweight buffers
Rationale: Rail jack bolts adjust for building compression.
Question 11: What type of flex is used to pipe a switch in a wet location?
A) Rigid conduit
B) Liquidtight flex
C) EMT conduit
D) PVC conduit
Rationale: Liquidtight flex is suitable for wet locations.
, Question 12: What does the designation 3/8" 6 x 30 improved plow steel mean?
A) 6 wires per strand, 30 strands
B) 6 strands, 30 wires per strand
C) 3/8" diameter, 6 strands
D) 30 wires total
Rationale: It indicates 6 strands with 30 wires each, high-strength cable.
Question 13: How should manila rope be prevented from unraveling?
A) Tape wrapping
B) Whipping
C) Heat sealing
D) Knotting
Rationale: Whipping secures rope ends to prevent unraveling.
Question 14: When handling a freight platform, what should be considered?
A) Store flat
B) Handle on edge, move on rollers
C) Stack vertically
D) Lift by center
Rationale: Handling on edge with rollers prevents damage.
Question 15: What is true about capstans?
A) They are portable
B) Fasten to a beam, interrupt by easing rope
C) Used only for maintenance
D) Require hydraulic power
Rationale: Capstans are fastened to beams, and hoisting is interrupted by easing the rope.
Question 16: What is the correct minimum spacing for Crosby clips?
A) 2 times rope diameter
B) 6 times rope diameter
C) 10 times rope diameter
D) 12 times rope diameter
Rationale: Crosby clips require spacing of 6 times the rope diameter.
Question 17: What is the purpose of a governor in an elevator system?
A) Control motor speed
B) Activate safety brakes
C) Adjust counterweight
D) Regulate door operation
Rationale: Governors detect overspeed and activate safety brakes.
Question 18: What is the ASME A17.1 code requirement for hydraulic elevator pits?
A) No water accumulation
B) Sump pump or drain
C) Open ventilation
D) Concrete sealing
Rationale: ASME A17.1 requires a sump pump or drain in pits.
Certified Solutions | 2025/2026 Edition
Verified Questions and Correct Answers | 100% Accurate | Graded A+
Introduction
This complete and certified resource covers the Class 200 NEIEP Final Exam along with 80
quizzes, featuring verified questions and correct solutions, fully updated for the 2025/2026
academic year. Designed to reflect current NEIEP standards, this compilation supports
mastery of key concepts for elevator mechanics and apprenticeship success.
Answer Format
Correct answers are marked in bold and green to ensure fast, effective, and accurate review.
Class 200 NEIEP Final Exam
Question 1: Which lay of wire rope has the strand wires in line with the rope axis?
A) Lang lay
B) Regular lay
C) Alternate lay
D) Reverse lay
Rationale: Regular lay has strand wires aligned with the rope axis, reducing wear.
Question 2: At what speed should counterweight safeties be set to trip?
A) Same as car governor
B) Up to 10% higher than car governor
C) 20% lower than car governor
D) Twice the car speed
Rationale: Counterweight safeties trip at up to 10% higher speed for safety margins.
Question 3: Which type of safety uses an oil buffer between the car and safety planks?
A) Type A
B) Type B
C) Type C
D) Type D
Rationale: Type B safeties use oil buffers to absorb impact.
Question 4: What is the minimum size wire allowed for 110VAC lighting circuits to elevator
cars?
A) 14 AWG
B) 12 AWG
C) 10 AWG
D) 16 AWG
Rationale: 12 AWG is the minimum for 110VAC lighting per code.
Question 5: What is the breaking strength for 1 1/8" nylon rope with a safety factor of 5?
A) 10,000 lbs
,B) 15,000 lbs
C) 20,000 lbs
D) 25,000 lbs
Rationale: Per Table 1, 1 1/8" nylon rope has a breaking strength of 15,000 lbs with a safety
factor of 5.
Question 6: What component engages the car door to the hoistway door during opening and
closing?
A) Door operator
B) Door clutch
C) Interlock
D) Retiring cam
Rationale: The door clutch couples car and hoistway doors for synchronized movement.
Question 7: How often must wires in high-rise raceways be supported?
A) Every 50 feet
B) Every 100 feet
C) Every 150 feet
D) Every 200 feet
Rationale: Code requires wire support every 100 feet in high-rise raceways.
Question 8: If voltage is present at the generator armature but not at the motor armature,
what is likely wrong?
A) Motor failure
B) Open loop circuit
C) Faulty governor
D) Broken sheave
Rationale: An open loop circuit prevents voltage transfer to the motor.
Question 9: How should passenger hoistway doors be stored?
A) Flat on the floor
B) Vertically on the long edge
C) Stacked horizontally
D) Leaning against a wall
Rationale: Vertical storage on the long edge prevents damage.
Question 10: What adjusts to reduce building compression effects on an elevator?
A) Governor ropes
B) Rail jack bolts
C) Door tracks
D) Counterweight buffers
Rationale: Rail jack bolts adjust for building compression.
Question 11: What type of flex is used to pipe a switch in a wet location?
A) Rigid conduit
B) Liquidtight flex
C) EMT conduit
D) PVC conduit
Rationale: Liquidtight flex is suitable for wet locations.
, Question 12: What does the designation 3/8" 6 x 30 improved plow steel mean?
A) 6 wires per strand, 30 strands
B) 6 strands, 30 wires per strand
C) 3/8" diameter, 6 strands
D) 30 wires total
Rationale: It indicates 6 strands with 30 wires each, high-strength cable.
Question 13: How should manila rope be prevented from unraveling?
A) Tape wrapping
B) Whipping
C) Heat sealing
D) Knotting
Rationale: Whipping secures rope ends to prevent unraveling.
Question 14: When handling a freight platform, what should be considered?
A) Store flat
B) Handle on edge, move on rollers
C) Stack vertically
D) Lift by center
Rationale: Handling on edge with rollers prevents damage.
Question 15: What is true about capstans?
A) They are portable
B) Fasten to a beam, interrupt by easing rope
C) Used only for maintenance
D) Require hydraulic power
Rationale: Capstans are fastened to beams, and hoisting is interrupted by easing the rope.
Question 16: What is the correct minimum spacing for Crosby clips?
A) 2 times rope diameter
B) 6 times rope diameter
C) 10 times rope diameter
D) 12 times rope diameter
Rationale: Crosby clips require spacing of 6 times the rope diameter.
Question 17: What is the purpose of a governor in an elevator system?
A) Control motor speed
B) Activate safety brakes
C) Adjust counterweight
D) Regulate door operation
Rationale: Governors detect overspeed and activate safety brakes.
Question 18: What is the ASME A17.1 code requirement for hydraulic elevator pits?
A) No water accumulation
B) Sump pump or drain
C) Open ventilation
D) Concrete sealing
Rationale: ASME A17.1 requires a sump pump or drain in pits.
