ICC REINFORCED CONCRETE / FINAL CODE
TEST- 60 QUESTIONS / NEWEST
COMPREHENSIVE STUDY GUIDE – EXPERT
STRATEGIES, REVIEW OF KEY QUIZZES, AND
PRACTICE QUESTIONS FOR GUARANTEED
SUCCESS (PASS GUARANTEED)
An acceptable reinforcing steel support mechanism for a 24-inch deep footing are?
-precast dobie blocks
-large,solid pieces of glass
-masonry CMU pieces
-wooden blocks -CORRECT ANSWER Precast dobie blocks
all of the following are true except ?
---Minimum concrete cover for bundled bars of any size need not be greater than 2 inches, unless they
are in a member that's permanently cast against earth
---specified concrete cover for headed shear stud reinforcement shall not be less then the cover
requirement for the member in which the stud reinforcement is located
,---Concrete cover for the flexural members, walls, and compression members with an effective depth of
8-inches can vary -3/8 of an inch
---Concrete cover for members in highly corrosive environments will typically remain the same as cast
against earth -CORRECT ANSWER Concrete cover for members in highly corrosive environments
will typically remain the same as cast agonist earth
As a general rule, Lap splicing bar larger then NO.11 Is?
-not permitted
-permitted
-permitted if bars will be in tension within the structural member
-permitted only if bars are within a bundle -CORRECT ANSWER not permitted
before new concrete is placed, construction joints must be?
-blown free of dirt and debris
-wetted ,and standing water removed
-sand blasted
- treated with a bonding agent -CORRECT ANSWER wetted, and standing water removed
grade 60 reinforcing steel has an ultimate strength of?
-60,000
-75,000
-90,000
-100,000 -CORRECT ANSWER 90,000 psi
The__________may waive requirements for the employment of a special inspection agency if he/she
finds that the construction is of minor nature.
-building official
, -engineer or architect of record
-owner
-all of the above -CORRECT ANSWER building official
what is the maximum allowable center to center spacing of spliced bars in a non-contact lap splice for
the flexural members?
-6 inches
-4 inches
-8 inches
-2 inches -CORRECT ANSWER 6 inches
Drilled cast-in place concrete piles that poured with concrete having an f'c of 2500 psi need special
inspection?
-only when required by the building official
-at the engineers discretion
-at all times
-when poured with concrete having an air entrainment greater then 3% -CORRECT ANSWER at all
times
The type of portland cement best suited for general use when a moderate heat of hydration is desired is
- Type I
- Type II
- Type III
- Type V -CORRECT ANSWER Type II
Concrete containing pre-stressed tendons, embedded aluminum, or cast against stay in place galvanized
steel forms shall not contain?
TEST- 60 QUESTIONS / NEWEST
COMPREHENSIVE STUDY GUIDE – EXPERT
STRATEGIES, REVIEW OF KEY QUIZZES, AND
PRACTICE QUESTIONS FOR GUARANTEED
SUCCESS (PASS GUARANTEED)
An acceptable reinforcing steel support mechanism for a 24-inch deep footing are?
-precast dobie blocks
-large,solid pieces of glass
-masonry CMU pieces
-wooden blocks -CORRECT ANSWER Precast dobie blocks
all of the following are true except ?
---Minimum concrete cover for bundled bars of any size need not be greater than 2 inches, unless they
are in a member that's permanently cast against earth
---specified concrete cover for headed shear stud reinforcement shall not be less then the cover
requirement for the member in which the stud reinforcement is located
,---Concrete cover for the flexural members, walls, and compression members with an effective depth of
8-inches can vary -3/8 of an inch
---Concrete cover for members in highly corrosive environments will typically remain the same as cast
against earth -CORRECT ANSWER Concrete cover for members in highly corrosive environments
will typically remain the same as cast agonist earth
As a general rule, Lap splicing bar larger then NO.11 Is?
-not permitted
-permitted
-permitted if bars will be in tension within the structural member
-permitted only if bars are within a bundle -CORRECT ANSWER not permitted
before new concrete is placed, construction joints must be?
-blown free of dirt and debris
-wetted ,and standing water removed
-sand blasted
- treated with a bonding agent -CORRECT ANSWER wetted, and standing water removed
grade 60 reinforcing steel has an ultimate strength of?
-60,000
-75,000
-90,000
-100,000 -CORRECT ANSWER 90,000 psi
The__________may waive requirements for the employment of a special inspection agency if he/she
finds that the construction is of minor nature.
-building official
, -engineer or architect of record
-owner
-all of the above -CORRECT ANSWER building official
what is the maximum allowable center to center spacing of spliced bars in a non-contact lap splice for
the flexural members?
-6 inches
-4 inches
-8 inches
-2 inches -CORRECT ANSWER 6 inches
Drilled cast-in place concrete piles that poured with concrete having an f'c of 2500 psi need special
inspection?
-only when required by the building official
-at the engineers discretion
-at all times
-when poured with concrete having an air entrainment greater then 3% -CORRECT ANSWER at all
times
The type of portland cement best suited for general use when a moderate heat of hydration is desired is
- Type I
- Type II
- Type III
- Type V -CORRECT ANSWER Type II
Concrete containing pre-stressed tendons, embedded aluminum, or cast against stay in place galvanized
steel forms shall not contain?
