Massachusetts 1A Hoisting License Exam Questions and Answers Latest Updated 2024/2025 | Scored A+

Massachusetts 1A Hoisting License Exam Questions and Answers Latest Updated 2024/2025 | Scored A+. Where should a license or temporary permit be located during time of operation of equipment:  Shall be carried ON the person at all times; in the case of a temporary permit the person shall also carry their drivers license 2. Whats the fine for violating section 53, 53a or 54:  No less than $500 and no more than $3,000, or by imprisonment of no more than 3 months, or both fine and imprisonment 3. Whats the fine for permitting an unlicensed person to operate machinery: -  No less than $1,000 and no more than $3,000, or imprisonment of no more than 3 months, or both fine and imprisonment 4. Whats the fine for violating section 42 to 51, or prevents an inspector from entering the premises:  No less than $10 no more than $300, or by imprisonment of upto 3 months 5. Whats the purpose of 520CMR 6.00:  To establish reasonable requirements to protect the public safety of the citizens of the commonwealth from the hazards inherent in the operation of housting machinery by establishing min Massachusetts 1A Hoisting License Questions and Answers Updated 2024/2025 | Scored A+ 2 / 23 standards neccessary to obtain a hoisting machinery operators license or temp permit 6. ANSI: American National Standards Institute 7. Apprentice license: A document issued by the dept upon proof of registratio at a training facility and with the division of apprentice training within the dept of labor standards, which enables the holder to operate hoisting machinery under the direct guidance and supervision of a duly licensed person licensed to operate the category of hoisting machinery for which documentation is issued 8. ASME: American Society of Mechanical Engineers 9. cargo: A load, quantity or volume that can be processed or transported 10. Apprentice licensee: A person, 18 or older, registered with the dept of labor standards and has obtained an apprentice license to operate while under direct guidance and supervision of a duly licensed person 11. Chief: The chief of inspections-mechanical of the dept of public safety 12. Compact hoisting machinery: Machinery wirh a gross vehicle weight not exceeding 10,000 lbs, excluding Class 1, Class 3 and Class 4 hoisting machinery as listed in 520CMR 6.10. Machinery operated under temp permit may not exceed 8,000lbs 13. DAT: Division of Apprentice Training 3 / 23 14. Department: Dept of Public Safety 15. DOT: Department of Transportation 16. Emergency procedure: Actions required to be taken when imminent danger may occur to prevent damage to life, property, or to public safety 17. Company license: Issued by an exempt company that has a dept approved in service training program and is only valid for machinery used on company property 4 / 23 18. fork lift: Any mobile powered truck used to carry, push, lift, stack or tier materialsEXCLUDING earth moving, over the road haulage trucks and equipment which was designed to move earth but modified to accept forks 19. Hoisting machinery: Derricks, cableways, machinery used for discharging cargoes, and temp elevator cars used on excavation work or hoisting building materials, when the motive power to operate such machinery is mechanical and other than steam, and any other equipment that has the MIN capability of hoisting a load HIGHER THAN 10 FT, and either the capability of lifting loads GREATER THAN 500 LBS or the capacity of the bucket EXCEEDS 1/4 CUBIC YARDS; overhead bridge cranes, electric or air driven hoists, specialty equipment as catagorized under 520CMR 6.00 20. incedent: A situation that results in serious injury, property damage or any condition that is necessary for the preservation of the public health or safety 21. Injury and incedent documentation: A form furnished by the department detailing all specific info regarding any serious injury, property damage or mechanical failure that may have occurred 22. inspector: A District Engineering Inspector employed by the Department 23. Manufacturer approved attachment: Attachable equipment tailored to perform a particular task, designed or approved for use in accordance with the equipment 5 / 23 manufacturers spec's. If the manufacturer doesnt exist, a MASS registered professional engineer shall review and approve in writing the actions and reasons for said specs to the attachable equipment 24. mechanical failure: Damage to or breakdown of hoisting machinery which affects the capacity or safe operation of the equipment per the manufacturers specifications 25. 1%: If a crane is out of level by 1%, you can lose upto 50% capacity 26. 3300 pounds: Pounds weight of one cubic yard of soil 27. 125 pounds: Weight of one cubic foot of soil 28. operator's manual: The document created by the manufacturer of the hoisting equip. That contains the required procedures and forms for the safe operatiob of hoisting machinery ar the stated site pertaining to that spec. Equip. 29. placard: A dept issued certificate posted on machinery which acts as a notice of the unsafe conditiob of the machinery 30. Property Damage: Damage of private or public property that exceeds $5,000 per incident 31. qualified welder: A welder certified by the American Welding Society (AWS) 32. SAE: Society of Automotive Engineers 6 / 23 33. serious injury: A personal injury/illness that results in death,dismemberment,significant disfigurement, permanant loss of the use of a body organ,member,functiob or system, a compound fracture or other significant injury/illness 34. Signal Person: A trained individual qualified in the use of signals to direct the operator of hoisting equipment or warn of possible or existing hazards through the use of hand signals,audible signals or flashing lights (see 520 CMR 6.00 apx A) 35. Temporary Permit: Non-renewable permit to operate machinery, with a gross vehicle weight not exceeding 8,000 lbs issued by dept approved short term rental entity for no more than 14 consec. Days 36. Temp permit holder: Person who is 18 or older, holds a valid drivers license andhas obtained a temp permit. 37. Utility: Any organization or company that provides electricity, natural gas, phone or cable services to public 38. Ansi standards for operating: B30.2-2011 overhead or Gantry Cranes (Top running bridge, single or mult girder, top running trolly hoist) B30.3-2012 tower cranes B30.5-2011 mobile & locomotive cranes B30.9-2010 Slings 7 / 23 B30.11-2010 monorails and underhung cranes B30.16-2012 overhead hoists (underhung) B30.17-2006 (R2012) overhead and gantry cranes (Top running bridge, single girder or underhung hoist) B30.20-2010 Below the hook lifting Devices B30.22-2010 Articulating Boom Cranes B30.26-2010 rigging hardware, incl. Errata (2011) 39. Sae standards for operating: J excavator and backhoe signals 40. Osha regulations for operating: 29 CFR 1926 safety and health regulations for construction 29 CFR 1910 occupational safety and health standards 8 / 23 41. Regulations for operating: 220 CMR 99.00 procedures for the determination and enforcement of violations of MGL c 88, SS 40 through 40E ("dig safe") 42. Operating procedures for hoisting machinery: A) maintenance : maintenance, repair and refueling shall be done when the machine is inoperable and secureB) visual inspection shall be made DAILY of wire ropes,bearings,gears,friction clutches, brakes, chain drives ans other parts subject to wear on all hoisting machinery to ensure against development of unsafe conditions. A DAILY LOG SHEET IN ACCORDANCE TO 29 CFR 1926 and 29 CFR 1910 inspectional methods shall be available to the dept during the useful life of the machine 43. Operating procedures for hoisting machinery: In addition: 1) a Written and signed record of all inspections shall be kept with the hoisting machinery and made available at the site for examination by the department that conforms the regulations are 29 CFR 1926.1412 2) prior to starting any machinery operator must complete walk around of the equipment to verify people are clear of equip and that its safe condition 3) Operator shall not engage in any practice that will divert their attention while 9 / 23 engaged in operating the hoisting machinery 4) At no time shall the operator of machinery operate or be required to operate the machinery beyond it's rated capacity without the manufactures written approval which shall include a new chart showing the new limitations. other than assembly/disassembly the use of the load moment indicator override key ,or entering a false crane set up criteria to increase rated capacity, is strictly forbidden 5) operator shall operate hoisting machinery only one fully attentive the operator shall not operate the equipment erratically and/or under the influence of alcohol or drugs when operators physically or mentally unfit the operation shall not operate with the machinery 6) prior to operating hoisting machinery with a rotating superstructure, safety procedures such as but not limited to the erection of barricades,warning lines and other procedures shall be used to prevent entry into the swinging superstructures radius