NACE CIP 1 CBT Exam (Quizzes and Study Questions) with Certified Answers

NACE CIP 1 CBT Exam (Quizzes and Study Questions) with Certified Answers How is the process of steel corrosion ALWAYS described? - Answer ️️ -electrochemical Based on the galvanic series presented in the NACE CIP Level 1 Manual, which three can be used effectively as galvanic anodes for carbon steel? - Answer ️️ -zinc, aluminum, magnesium A decrease in temperature will generally cause the corrosion rate to _____ - Answer ️️ - decrease The electrolyte is a medium which carries the following type of current? - Answer ️️ -Ionic Corrosion occurring uniformly across a surface is called _____ - Answer ️️ -general corrosion When a conflict occurs on a coatings project, as the inspector, the preferred first course of action is to _____ - Answer ️️ -actively listen and endeavor to understand the positions of others A proper coating specification should contain information regarding ____, ____, and ____ - Answer ️️ -surface preparation standards, safety, and locations to be used Is it ever okay to accept a gift from a contractor? - Answer ️️ -NO What should you do if you find discrepancies between the specification and the coating manufacturer's technical data sheet? - Answer ️️ -seek written clarification from the owner's representative What are the general components of inspection reports? - Answer ️️ -- results of inspection tests - location(s) of work - details of preparation and application Inspection reports typically provide sufficient detail permitting the owner to evaluate ___ ___ ___ ___ - Answer ️️ -- contractor's performance - inspector's performance - job progress - work interruptions As an inspector headed to the job site for the first time, where would you always find instruction regarding appropriate types of PPE? - Answer ️️ -Safety Data Sheet (SDS), previously called MSDS Materials inventory report should contain which of the following? - Answer ️️ -- quantity of each component of each material onsite - material batch numbers - date of materials arrival at job site and storage information The primary function of the coating inspector is _____ - Answer ️️ -specification compliance High humidity in the air during coating application can cause _____ - Answer ️️ -solvent entrapment The temperature at which moisture condenses on a surface is called _____ - Answer ️️ -dew point Where should the steel surface temperature reading be taken? - Answer ️️ -at the actual work location What type of water should be added to a sling psychrometer? - Answer ️️ -distilled Which type of coating is manufactured with the specific components added to slow down the activity of the electrochemical cell? - Answer ️️ -inhibitive Which coating component forms a stable film that retains its characteristic properties? - Answer ️️ -binder/resin A barrier coating interrupts the ______ of the electrochemical cell. - Answer ️️ -electrolyte List the three mechanisms by which coatings adhere to a substrate - Answer ️️ -1. Polar 2. Chemical 3. Mechanical What is the rule for coating work when it comes to Dew Point and Steel Temperature? - Answer ️️ -Steel Temperature must be 5 degrees less than the Dew Point What characteristics of solvents influence coatings? - Answer ️️ -- solvency power - volatility The contractor's sling psychrometer gives a different reading than your electric hygrometer. What would you do first as an inspector? - Answer ️️ -verify calibration of both instruments Which of the following coating are co-reacting? - Answer ️️ -- polyurethane - epoxy Fusion Bond Epoxy (FBE) is most commonly used to coat ____ - Answer ️️ -pipe Which coatings may require external moisture to cure? - Answer ️️ -- single component polyurethane - solvent borne inorganic zinc Amine blush is likely to occur with which type of coating? - Answer ️️ -epoxy Which type of coating cures the fastest? - Answer ️️ -Polyurea When an inorganic Zinc Rich primer is applied too heavily a common result is ______ - Answer ️️ -mud cracking Commonly used primers for steel structures are ? - Answer ️️ -- epoxy - inorganic zi