Inspector Exam Practice Questions and
Correct Answers with Rationales —
Plumbing, Mechanical, Electrical, and Life-
Safety Inspections | Instant PDF Download
Prepare by reviewing inspection sequences, life-safety
principles, and the applicable adopted codes and local
amendments. This 100-question practice exam covers
residential plumbing, water heaters, mechanical systems,
electrical coordination, egress and stairs, fireblocking, and
trade-inspection approvals; each question includes its correct
answer and a three-sentence explanation.
Question 1: During a plumbing rough-in inspection, which
condition best supports approval of a concealed drain, waste,
and vent system? A) All joints are assembled, the required
test has been completed, and the system holds without
leakage. B) The visible portions appear dry, although the
system has not been tested. C) The piping is covered, but the
installer reports that it was tested before concealment. D)
The system drains when a nearby fixture is operated. Correct
Answer: A — All joints are assembled, the required test has
been completed, and the system holds without leakage.
Rationale: A completed, successful test provides evidence
that concealed joints and piping are sound. Testing before
concealment allows defects to be identified while they
,remain accessible. Visual dryness or an installer’s report
alone does not demonstrate that the entire system passed
the required test.
Question 2: A lavatory trap is installed, but its trap arm has no
vent connection before it joins a larger drain. What is the
principal concern? A) The trap will receive too much hot
water. B) Drainage may siphon water from the trap and allow
sewer gas into the room. C) The fixture will require a larger
water-supply pipe. D) The drain will necessarily become a
potable-water cross-connection. Correct Answer: B —
Drainage may siphon water from the trap and allow sewer
gas into the room. Rationale: Venting helps maintain
pressure conditions that protect a fixture trap’s water seal.
If the seal is lost, sewer gases can enter the occupied space.
A larger supply pipe does not correct a trap-arm venting
defect.
Question 3: A rough-in inspection reveals a water-supply pipe
rubbing against a sharp metal edge at a framing penetration.
What is the best inspection response? A) Approve it if no leak
is currently visible. B) Require the pipe to be replaced with a
larger diameter. C) Require suitable protection or clearance to
prevent abrasion and damage. D) Require the pipe to be
wrapped in combustible insulation. Correct Answer: C —
Require suitable protection or clearance to prevent abrasion
and damage. Rationale: Contact with a sharp edge can
wear through piping as the building moves or the pipe
,expands and contracts. A protective plate, bushing, or
corrected route can prevent that damage. Replacing the
pipe with a larger diameter does not address the abrasion
hazard.
Question 4: A toilet is set over a drain opening with a loose,
visibly damaged sealing ring. What should the inspector do?
A) Accept it if the toilet does not rock. B) Accept it if the floor
around it is dry. C) Add sealant around the outside of the
toilet base. D) Require a proper, intact seal and correct
installation before approval. Correct Answer: D — Require a
proper, intact seal and correct installation before approval.
Rationale: A properly installed seal prevents leakage and
sewer-gas escape at the toilet connection. A stable toilet can
still leak if the seal is defective. Exterior caulk cannot
reliably replace a sound seal at the drain outlet.
Question 5: What is the most useful purpose of inspecting
plumbing before walls and ceilings are closed? A) To verify
concealed piping, supports, connections, and required tests
while they are accessible. B) To confirm paint colors around
fixtures. C) To determine the final water bill. D) To avoid
inspecting any completed fixtures. Correct Answer: A — To
verify concealed piping, supports, connections, and required
tests while they are accessible. Rationale: Rough-in
inspections assess components that would be difficult to
examine after concealment. They also allow required tests
and corrections to occur before finishes are installed. A
, rough-in inspection does not replace the final inspection of
fixtures and operation.
Question 6: During a final plumbing inspection, a newly
installed fixture drains slowly and gurgles. Which action is
most appropriate? A) Approve it because some gurgling is
normal for every fixture. B) Investigate for a drainage or
venting defect and require correction if noncompliant. C)
Increase the water pressure to the fixture. D) Seal the
overflow opening permanently. Correct Answer: B —
Investigate for a drainage or venting defect and require
correction if noncompliant. Rationale: Slow drainage and
gurgling can indicate a restriction or inadequate venting.
The inspector should evaluate the system rather than
assume the symptoms are harmless. Increasing supply
pressure does not correct a drainage or venting problem.
Question 7: A contractor proposes concealing a water-supply
joint that remains visibly incomplete at rough-in. What is the
soundest inspection decision? A) Approve it if the pipe is new.
B) Approve it if the homeowner accepts the risk. C) Withhold
approval until the joint is completed and the required test
passes. D) Approve it if the joint is near a shutoff valve.
Correct Answer: C — Withhold approval until the joint is
completed and the required test passes. Rationale: An
incomplete joint cannot be demonstrated to be leak-free or
properly assembled. Concealment would make inspection