1|Page
FLORIDA STATE FIRE INSTRUCTOR 3 EXAM WITH 250
UPDATED VERIFIED QUESTIONS AND DETAILED
CORRECT ANSWERS WITH RATIONALES (ALREADY
GRADED A+)||NEWEST EXAM!!!
What is the mission of the fire service - Answers-To save
lives and protect property
What NFPA standard establishes basic training criteria for
Firefighter I and Firefighter II? - Answers-1001
a ___ is a collection of rules enacted by law in a particular
jurisdiction - Answers-Code
What best describes the action first taken after an alert to
the station - Answers-Dispatching of emergency servies
responders
the use of ten codes in radio transmissions was replaced
when agencies began to adopt which of the following -
Answers-National Incident Management system (NIMS)
,2|Page
What task may a telecommunications center be assigned
during a progress report - Answers-Providing periodic time
transmission
what best describes when an SCBA cylinder needs to be
replaced - Answers-During inspection if cylinder contains
less than 90% of capacity
which type of rope is the only rope required to have a rope
log - Answers-Life Safety Rope
which part of the rope is used to tie a knot or hitch -
Answers-Working
which type of knot can be used to secure a victims hands
or feet to drag a victim to safety - Answers-Handcuff
Once a search is complete, a FF should - Answers-Report
promptly to the supervisor
What are the two objectives for a structural search -
Answers-Search for life; assess fire conditions
, 3|Page
what types of extrication method is used to stabilize a
vehicle that is upside down or lying on its side - Answers-
Buttress tension System
what initial action is next priority after stabilizing the scene
- Answers-stabilize the victim
what type of structural collapse occurs when the floor and
or roof assemblies on both sides of a load bearing wall
collapse, allowing a good chance of victim survival -
Answers-A-Frame
in the OATH method of signaling on a search line, two tugs
represents - Answers-Advance
What type of tool is a pike pole - Answers-Push pull
cutting edges on axes should be inspected for - Answers-
chips, cracks, or spurs.
p.595
FLORIDA STATE FIRE INSTRUCTOR 3 EXAM WITH 250
UPDATED VERIFIED QUESTIONS AND DETAILED
CORRECT ANSWERS WITH RATIONALES (ALREADY
GRADED A+)||NEWEST EXAM!!!
What is the mission of the fire service - Answers-To save
lives and protect property
What NFPA standard establishes basic training criteria for
Firefighter I and Firefighter II? - Answers-1001
a ___ is a collection of rules enacted by law in a particular
jurisdiction - Answers-Code
What best describes the action first taken after an alert to
the station - Answers-Dispatching of emergency servies
responders
the use of ten codes in radio transmissions was replaced
when agencies began to adopt which of the following -
Answers-National Incident Management system (NIMS)
,2|Page
What task may a telecommunications center be assigned
during a progress report - Answers-Providing periodic time
transmission
what best describes when an SCBA cylinder needs to be
replaced - Answers-During inspection if cylinder contains
less than 90% of capacity
which type of rope is the only rope required to have a rope
log - Answers-Life Safety Rope
which part of the rope is used to tie a knot or hitch -
Answers-Working
which type of knot can be used to secure a victims hands
or feet to drag a victim to safety - Answers-Handcuff
Once a search is complete, a FF should - Answers-Report
promptly to the supervisor
What are the two objectives for a structural search -
Answers-Search for life; assess fire conditions
, 3|Page
what types of extrication method is used to stabilize a
vehicle that is upside down or lying on its side - Answers-
Buttress tension System
what initial action is next priority after stabilizing the scene
- Answers-stabilize the victim
what type of structural collapse occurs when the floor and
or roof assemblies on both sides of a load bearing wall
collapse, allowing a good chance of victim survival -
Answers-A-Frame
in the OATH method of signaling on a search line, two tugs
represents - Answers-Advance
What type of tool is a pike pole - Answers-Push pull
cutting edges on axes should be inspected for - Answers-
chips, cracks, or spurs.
p.595
