DHL Interview ATPL ACTUAL EXAM | WITH COMPLETE
QUESTIONS AND ANSWERS | 2025/2026 LATEST UPDATED | 100 %
RATED AND VERIFIED SOLUTIONS | GET AN A+
What is the VOR change over distance? - (ANSWER)60NM
What is the minimum distance between parallel runways? - (ANSWER)915m
what the key points of using Mode 2 for parallel runways? - (ANSWER)Only straight in
approaches allowed
interception angle of no more that 30 degrees
must be straight and level 1NM for localiser
must be straight and level 2NM for Glideslope
Minimum separation of 3NM on same Loc
Min separation of 2 NM on adjacent Loc
Missed approach tracks diverge by at least 30 degree
what is the minimum time a flight plan must be filed before departure - (ANSWER)60 minutes
,how does a pilot create a slip or a skid and how it is indicated on the turn co-ordinator? -
(ANSWER)Slip - opposite rudder to direction of turn = ball will be at the same side of the turn
Skid - too much rudder in the direction of the turn = ball will be on the opposite side to the turn
what time must ATC clocks be within? - (ANSWER)30 seconds
what are the Airspace separations rules for Class A - (ANSWER)IFR Only
What are the Airspace separation rules for Class B - (ANSWER)IFR and VFR seperated
What are the Airspace separation rules for Class C - (ANSWER)IFR separated from IFR
IFR Separated from VFR
VFR Info about VFR
Speed limited below FL100 250kts
IFR ( speed limit only on ATC instruction)
What are the Airspace separation rules for Class D - (ANSWER)IFR Separated from VFR
IFR Info about VFR
,VFR Info about VFR
Speed limit below FL100 250kts
what its the difference between class D and Class E airspace for VFR - (ANSWER)No ATC
required
No SVFR
What is Load Shedding - (ANSWER)Reducing electrical load on the system by turning of
unnecessary electrical components
how would an artificial feel unit be connected? - (ANSWER)In Parallel
otherwise if it failed it would stop the system
what are booster pumps - (ANSWER)low pressure centrifugal boots that supply fuel to the
engines.
why are booster pumps important? - (ANSWER)they prevent cavitation of the engine driven
pumps at high altitude.
, what is the purpose of baffle valves - (ANSWER)to prevent fuel flowing the the wing tips to
keep it in the centre near the pumps
what is a feeder box - (ANSWER)a box arounds the booster pumps that keeps the pumps
submerged in fuel to prevent cavitation
how do you switch off the magneto - (ANSWER)ground the primary circuit
how is the twin jet fuelled - (ANSWER)by fuel being pumped from the fuel truck
what type of fire extinguisher do you use on propane fire - (ANSWER)foam
what is the difference between IAS and CAS (calibrated Airspeed) - (ANSWER)corrected for
instrument positional errors
what is the difference between CAS and TAS (true Airspeed) - (ANSWER)Corrected for
changes in air Density
when is ground effect felt? - (ANSWER)half the wingspan from the ground
QUESTIONS AND ANSWERS | 2025/2026 LATEST UPDATED | 100 %
RATED AND VERIFIED SOLUTIONS | GET AN A+
What is the VOR change over distance? - (ANSWER)60NM
What is the minimum distance between parallel runways? - (ANSWER)915m
what the key points of using Mode 2 for parallel runways? - (ANSWER)Only straight in
approaches allowed
interception angle of no more that 30 degrees
must be straight and level 1NM for localiser
must be straight and level 2NM for Glideslope
Minimum separation of 3NM on same Loc
Min separation of 2 NM on adjacent Loc
Missed approach tracks diverge by at least 30 degree
what is the minimum time a flight plan must be filed before departure - (ANSWER)60 minutes
,how does a pilot create a slip or a skid and how it is indicated on the turn co-ordinator? -
(ANSWER)Slip - opposite rudder to direction of turn = ball will be at the same side of the turn
Skid - too much rudder in the direction of the turn = ball will be on the opposite side to the turn
what time must ATC clocks be within? - (ANSWER)30 seconds
what are the Airspace separations rules for Class A - (ANSWER)IFR Only
What are the Airspace separation rules for Class B - (ANSWER)IFR and VFR seperated
What are the Airspace separation rules for Class C - (ANSWER)IFR separated from IFR
IFR Separated from VFR
VFR Info about VFR
Speed limited below FL100 250kts
IFR ( speed limit only on ATC instruction)
What are the Airspace separation rules for Class D - (ANSWER)IFR Separated from VFR
IFR Info about VFR
,VFR Info about VFR
Speed limit below FL100 250kts
what its the difference between class D and Class E airspace for VFR - (ANSWER)No ATC
required
No SVFR
What is Load Shedding - (ANSWER)Reducing electrical load on the system by turning of
unnecessary electrical components
how would an artificial feel unit be connected? - (ANSWER)In Parallel
otherwise if it failed it would stop the system
what are booster pumps - (ANSWER)low pressure centrifugal boots that supply fuel to the
engines.
why are booster pumps important? - (ANSWER)they prevent cavitation of the engine driven
pumps at high altitude.
, what is the purpose of baffle valves - (ANSWER)to prevent fuel flowing the the wing tips to
keep it in the centre near the pumps
what is a feeder box - (ANSWER)a box arounds the booster pumps that keeps the pumps
submerged in fuel to prevent cavitation
how do you switch off the magneto - (ANSWER)ground the primary circuit
how is the twin jet fuelled - (ANSWER)by fuel being pumped from the fuel truck
what type of fire extinguisher do you use on propane fire - (ANSWER)foam
what is the difference between IAS and CAS (calibrated Airspeed) - (ANSWER)corrected for
instrument positional errors
what is the difference between CAS and TAS (true Airspeed) - (ANSWER)Corrected for
changes in air Density
when is ground effect felt? - (ANSWER)half the wingspan from the ground
