ASSE 15000 Practice Test 3 2025-2026 With
Complete Questions and Correct Answers |
Graded A+ | Verified Answers And Brand New
High priming water levels can adversely affect the operation of
supervisory air. What is not a step in testing the water level? - answer--
Close the priming level test valve before air discharges
The _____ valve shall be supervised closed in the pipeline to the hose
valve header - answer--control
A diesel fuel storage tank is required to always be a minimum of __ full.
- answer--2/3
A fire pump controller shall be in a fully functional state within ___
seconds of AC power available. - answer--10
The standpipe system demand shall include 500 gpm for the first
standpipe and ___ gpm for each additional standpipe until the total
system demand is simultaneously met. - answer--250
Water motor gongs and pressure switch alarm devices shall be
inspected: - answer--quarterly
,A temporary standpipe used during construction must be at least ___ in
diameter - answer--4 inches
Blue color coding on a sprinkler indicates it has a temperature rating
between _____. - answer--250 - 300 degrees F
When swapping out pressure gauges, it is important to verify the arrow
on the 3-way valve is pointed in the proper direction before removing
the gauge and once the gauge is removed, the 3-way valve must be
flushed adequately so any debris that may have accumulated does not
end up in the new gauge. - answer--True
According to NFPA 20, a _____ refill valve shall be used for each water
supply tank used for fire protection. - answer--automatic
All sprinkler pressure-reducing valves shall be inspected qurterly to
verify the valves are in the following condition except: - answer--in the
closed position
Which type of pipe is not approved for standpipes - answer--CPVC
Foam concentrate strainers shall be inspected: - answer--quarterly
, A fire pump water supply must be ___. - answer--Adequate and
dependable
The shut-off head shall not exceed ___ of rated head for any pump. -
answer--140%
The top hose outlet in a buuilding under construction must be
maintained within _____ floors of the highest forms, staging and similar
combustibles at all times. - answer--one
The drain riser shall be equipped with tees that are of the same size as
the discharge outlets of the ___ devices to be tested and shall be
located at least every other floor. - answer--pressure regulating
What is the minimum suction pressure required at the pump suction
flange when a suction tank is installed at or above the base of the fire
pump running at 150% capacity? - answer---3
What type of standpipe is not required to be hydrostatically tested at
200 psi or 50 psi in excess of 150 psi? - answer--manual standpipe
When soldering copper, flux should be applied to ___. - answer--the
inside of the fitting and the outside of the tube
Complete Questions and Correct Answers |
Graded A+ | Verified Answers And Brand New
High priming water levels can adversely affect the operation of
supervisory air. What is not a step in testing the water level? - answer--
Close the priming level test valve before air discharges
The _____ valve shall be supervised closed in the pipeline to the hose
valve header - answer--control
A diesel fuel storage tank is required to always be a minimum of __ full.
- answer--2/3
A fire pump controller shall be in a fully functional state within ___
seconds of AC power available. - answer--10
The standpipe system demand shall include 500 gpm for the first
standpipe and ___ gpm for each additional standpipe until the total
system demand is simultaneously met. - answer--250
Water motor gongs and pressure switch alarm devices shall be
inspected: - answer--quarterly
,A temporary standpipe used during construction must be at least ___ in
diameter - answer--4 inches
Blue color coding on a sprinkler indicates it has a temperature rating
between _____. - answer--250 - 300 degrees F
When swapping out pressure gauges, it is important to verify the arrow
on the 3-way valve is pointed in the proper direction before removing
the gauge and once the gauge is removed, the 3-way valve must be
flushed adequately so any debris that may have accumulated does not
end up in the new gauge. - answer--True
According to NFPA 20, a _____ refill valve shall be used for each water
supply tank used for fire protection. - answer--automatic
All sprinkler pressure-reducing valves shall be inspected qurterly to
verify the valves are in the following condition except: - answer--in the
closed position
Which type of pipe is not approved for standpipes - answer--CPVC
Foam concentrate strainers shall be inspected: - answer--quarterly
, A fire pump water supply must be ___. - answer--Adequate and
dependable
The shut-off head shall not exceed ___ of rated head for any pump. -
answer--140%
The top hose outlet in a buuilding under construction must be
maintained within _____ floors of the highest forms, staging and similar
combustibles at all times. - answer--one
The drain riser shall be equipped with tees that are of the same size as
the discharge outlets of the ___ devices to be tested and shall be
located at least every other floor. - answer--pressure regulating
What is the minimum suction pressure required at the pump suction
flange when a suction tank is installed at or above the base of the fire
pump running at 150% capacity? - answer---3
What type of standpipe is not required to be hydrostatically tested at
200 psi or 50 psi in excess of 150 psi? - answer--manual standpipe
When soldering copper, flux should be applied to ___. - answer--the
inside of the fitting and the outside of the tube
