CATEGORY 3 NON-CAB OPERATED CRANE SAFETY NEWEST
ACTUAL 2025/2026 QUESTIONS AND CORRECT ANSWERS
VERIFIED/GRADED A+
Matching ID marks on rigging gear are required for: - -----
Answers---components that can be seperated
Rigging gear test and inspection records are required to be
kept on file: - -----Answers---until rplaced by a more current
record
Documented records are required for periodic inspections of
all rigging equipment.falsefalse - -----Answers---false
What are the two types of rigging gear inspections? - -----
Answers---periodic and pre-use
Who is required to perfom an inspection prior to using rigging
gear, and what is this inspection called? - -----Answers---the
user, preuse inspection
What is the minimum grade of chain required for chain slings?
- -----Answers---grad 80
,Chain slings used in cargo transfer should be inspected
annually. - -----Answers---False
A knot in a synthetic sling is allowed as long as it does not
cause permanent damage to the sling. - -----Answers---false
A metal mesh sling can remain in service if only one wire is
broken in the mesh. - -----Answers---False
Rigging hardware that is bent can be repaired by straightening
it back to original shape. - -----Answers---false
Rigging hardware such as eyebolts, links, rings, and shackles
are required to have a periodic inspection every 2 years. - ----
-Answers---False
Distorted rigging hardware must be: - -----Answers---
Removed from service and destroyed
Documentation for alteration or repair of rigging equipment is
required to be retained for: - -----Answers---the life of the
equipment
Which section of the NAVFAC P-307 is the rigging gear
section? - -----Answers---section 14
, It is okay to use home-made rigging gear as long as you are
lifting light loads. - -----Answers---false
When selecting rigging gear for a job, which of the statements
below should be followed? - -----Answers---all the above
What should be used between the rigging gear and the load to
prevent damage to the load and rigging? - -----Answers---
appropriate sling protection
Two people can operate a chain fall if the pull chain is too hard
for one person to pull while hoisting a load. - -----Answers--
-False
Pulls outside the plane of the eye are allowed on eyebolts as
long as the rated load has been decreased. - -----Answers---
False
The minimum depth of thread engagement for a 3/4 inch
eyebolt into a steel object is: - -----Answers---1 1/8th inch
An angular pull of 45° is allowed on non-shoulder type
eyebolts. - -----Answers---false
The rated load of swivel hoist rings must be reduced when
they are used for angular pulls. - -----Answers---false
ACTUAL 2025/2026 QUESTIONS AND CORRECT ANSWERS
VERIFIED/GRADED A+
Matching ID marks on rigging gear are required for: - -----
Answers---components that can be seperated
Rigging gear test and inspection records are required to be
kept on file: - -----Answers---until rplaced by a more current
record
Documented records are required for periodic inspections of
all rigging equipment.falsefalse - -----Answers---false
What are the two types of rigging gear inspections? - -----
Answers---periodic and pre-use
Who is required to perfom an inspection prior to using rigging
gear, and what is this inspection called? - -----Answers---the
user, preuse inspection
What is the minimum grade of chain required for chain slings?
- -----Answers---grad 80
,Chain slings used in cargo transfer should be inspected
annually. - -----Answers---False
A knot in a synthetic sling is allowed as long as it does not
cause permanent damage to the sling. - -----Answers---false
A metal mesh sling can remain in service if only one wire is
broken in the mesh. - -----Answers---False
Rigging hardware that is bent can be repaired by straightening
it back to original shape. - -----Answers---false
Rigging hardware such as eyebolts, links, rings, and shackles
are required to have a periodic inspection every 2 years. - ----
-Answers---False
Distorted rigging hardware must be: - -----Answers---
Removed from service and destroyed
Documentation for alteration or repair of rigging equipment is
required to be retained for: - -----Answers---the life of the
equipment
Which section of the NAVFAC P-307 is the rigging gear
section? - -----Answers---section 14
, It is okay to use home-made rigging gear as long as you are
lifting light loads. - -----Answers---false
When selecting rigging gear for a job, which of the statements
below should be followed? - -----Answers---all the above
What should be used between the rigging gear and the load to
prevent damage to the load and rigging? - -----Answers---
appropriate sling protection
Two people can operate a chain fall if the pull chain is too hard
for one person to pull while hoisting a load. - -----Answers--
-False
Pulls outside the plane of the eye are allowed on eyebolts as
long as the rated load has been decreased. - -----Answers---
False
The minimum depth of thread engagement for a 3/4 inch
eyebolt into a steel object is: - -----Answers---1 1/8th inch
An angular pull of 45° is allowed on non-shoulder type
eyebolts. - -----Answers---false
The rated load of swivel hoist rings must be reduced when
they are used for angular pulls. - -----Answers---false
