Boilermaker NCCER Test Questions and Answers
New Update 2026/2027 | Graded A+ | Guaranteed
Pass.
WHEN ARE STEEL CHAIN SLINGS RECOMMENDED?
WHEN RIGGING FROM 3 PONTS
A BIG CONTROL VALVE IS PULLED. WHO'S RESPONSIBLE FOR THE RIGGING?
CRANE OPERATOR AND RIGGER
3) WHAT SHOULD BE USED TO HOLD THE PIPE WHEN SETTING UP TWO 40-FOOT
JOINTS OF 16-NCH SID WT PPE?
DeuGGED ROLLER TOP JACKS
4) THE HITCH MADE BY WRAPPING THE SUNG AROUND THE LOAD, THEN
PASSING ONE EYE OF THE SLING THROUGHT CALLED
YOHOKER HITCH
WHEN SHOULD RIGGING MATERIAL BE ATTACHED TO A BEAM TIIAT IS BEING
DEMOLISHED?
BEFORE ANY BOLTS ARE REMOVED OR ANY CUTTING IS DONE ON THE BEAM
WHICH TYPE OF INSOLATION IS REQUIRED BEFORE A VESSEL IS ENTERED?
DocING, TAGGING, AND BLINDING LINES THAT FEED THE VESSEL
, ACCORDING TO OSHA OXVGEN AND ACETYLE CYLINDERS IN STORAGE MUST BE
SEPARATED WHAT
NUMUM
20ft
WHAT IS THE FIRST THING A BOILER MAKER SHOULD DO SEFORE CUTTING INTO A
TARK OR VESSEL DETERMINE THE CONTENT
WHAT TOOL IS NORMALLY USED TO CHECK THE ALIGNMENT ON THE HORIZONTAL
SEAMS OF THE SHELL PLATES??
A2 FOOT LEVEL
WHAT IS USED TO EXPAND TUBES INSIDE MUD AND STEAM DRUMS?
ROLLING MOTORS AND ESPANDERS
WHAT ACTION SHOULD BE TAKEN IF A BOILER TUBE FAILS?
(ckePLACE THE FAILEO TUBE
BEFOERE A WALL BURNER IS PULLED FOR INSPECTION.
OTHE FUEL GAS VALVE MuST E SHUT
WHAT DOES A GROOVED NUT ON AN ACETYLENE RIG INDICATE
O THE LEFT HAND THREAD IS FOR ACETYLANE USE ONLY
THERMAL BEVELINN OF PIPE IN PREPARATION FOR WELDING REQUIRESS THE USE
OF AN:
OXYFUEL TORCH
New Update 2026/2027 | Graded A+ | Guaranteed
Pass.
WHEN ARE STEEL CHAIN SLINGS RECOMMENDED?
WHEN RIGGING FROM 3 PONTS
A BIG CONTROL VALVE IS PULLED. WHO'S RESPONSIBLE FOR THE RIGGING?
CRANE OPERATOR AND RIGGER
3) WHAT SHOULD BE USED TO HOLD THE PIPE WHEN SETTING UP TWO 40-FOOT
JOINTS OF 16-NCH SID WT PPE?
DeuGGED ROLLER TOP JACKS
4) THE HITCH MADE BY WRAPPING THE SUNG AROUND THE LOAD, THEN
PASSING ONE EYE OF THE SLING THROUGHT CALLED
YOHOKER HITCH
WHEN SHOULD RIGGING MATERIAL BE ATTACHED TO A BEAM TIIAT IS BEING
DEMOLISHED?
BEFORE ANY BOLTS ARE REMOVED OR ANY CUTTING IS DONE ON THE BEAM
WHICH TYPE OF INSOLATION IS REQUIRED BEFORE A VESSEL IS ENTERED?
DocING, TAGGING, AND BLINDING LINES THAT FEED THE VESSEL
, ACCORDING TO OSHA OXVGEN AND ACETYLE CYLINDERS IN STORAGE MUST BE
SEPARATED WHAT
NUMUM
20ft
WHAT IS THE FIRST THING A BOILER MAKER SHOULD DO SEFORE CUTTING INTO A
TARK OR VESSEL DETERMINE THE CONTENT
WHAT TOOL IS NORMALLY USED TO CHECK THE ALIGNMENT ON THE HORIZONTAL
SEAMS OF THE SHELL PLATES??
A2 FOOT LEVEL
WHAT IS USED TO EXPAND TUBES INSIDE MUD AND STEAM DRUMS?
ROLLING MOTORS AND ESPANDERS
WHAT ACTION SHOULD BE TAKEN IF A BOILER TUBE FAILS?
(ckePLACE THE FAILEO TUBE
BEFOERE A WALL BURNER IS PULLED FOR INSPECTION.
OTHE FUEL GAS VALVE MuST E SHUT
WHAT DOES A GROOVED NUT ON AN ACETYLENE RIG INDICATE
O THE LEFT HAND THREAD IS FOR ACETYLANE USE ONLY
THERMAL BEVELINN OF PIPE IN PREPARATION FOR WELDING REQUIRESS THE USE
OF AN:
OXYFUEL TORCH
